£45.00 exc vat
£54.00 inc vat
In stock
The gear is not included as there are different degrees of arch gears fitted but from 1980 on, they fitted the 110 degree type which is the only one now available.
Also see MSSK2005 intermittent wipe conversion kit a necessity in this day and age.
Comes with a new park switch and if your loom is not making proper contacts a repair section with plug is available as 520161.
A new bracket in stainless steel and rubber sleeve to hold the motor are available as 37H4836.
£45.00 exc vat
£54.00 inc vat
In stockRecommended usage 1 x GXE7708 to fit one mini.
Plastic gear with 110 degree wiper sweep for all mk2/3 saloons and vans etc from about 1980 on. This gear has 46 teeth and some pre 1980 vans/pickups had 120 degree(stamped on gear) with same amount of teeth, but was replaced by this. MK1 originally ...
Mk3 round body type wiper motors sat on this black rubber insulation pad
When replacing the 520160A parking switch the inner contact areas on the wiring loom are also worn or damaged so we produced this socket and small length of loom.
Upgraded Mini Spares product in stainles steel. You probably will never break this item, you're more likely to buy it for it's looks. This mounting strap fits all late model cars with the round wiper motor. The strap is polished stainless steel compl...
For classic vehicles with self parking wipers.
We all love our classic vehicles and many of us use them all year round. This means facing the vagaries of the weather, and let’s face it, even summer weather is rarely as rain free as...
This is the spiral wound cable that is in the wiper rack tubes. It needs to be cut to length.
Total length uncut is 150cm.
Fits the end of the wiper motor to hold the outer casing to protect the rack cable which drives the wheel boxes. Not supplied with new motors.
Wiper motor fitting kit to fit all mk2 onwards wiper motors to the bulkhead.
Wiper motor kit for all mk2 onwards cars, includes wiper motor, motor gear, wheel boxes, outer tube kit, wiper rack and wiper motor ferrule.
Wiper motor kit for all mk2 onwards cars, includes wiper motor, motor gear, wheel boxes, outer tube kit, wiper rack and wiper motor ferrule.
Wiper motor fitting kit to fit all mk2 onwards wiper motors to the bulkhead.
Clip to retain the speedo cable to the bulkhead on pre 82 cars approx. This clip is also used to hold the loom to the inner wing on some cars.
Main wiring grommet that fits in the front parcel shelf. ID 12.5mm fits 35mm hole.
Interior lamp with a black on/off switch and pointed torpedo ends.
Also fitted many of the 1959on range of Austin A55/60 Cambridge, MG Magnette etc.
Also there was an alternative lamp with black switch and square ends 13H192 which w...
Battery bar and fitting kit for all pre 1990 cars whcih had the shorter battery bolts.
Mini Mk 4 998 oval centre dash,twin column stalks,rocker switches including rear fog and heated rear window,reverse lights and rear fog lamp is on headlamp circuit. Intertia starter. To go with AN145 rear loom.
mainly for 1980-1...
This will replace the orange lens fitted on the wing of all cars from 1986 on, fitted with an orange LED. If you need a new loom for this lamp see AFU3358. Sold singly. Does not require a resistor.
The smallest pre engaged starter motor available for the A series yet still producing 1.3KW of power! Ideal for race/tuned cars with high compression and cars that need more room for oil coolers etc. See GXE1004EVO for inertia.
Genuine Bosch lambda sensor, fitted to both the twin and single point injection cars and fitted in the same exhaust manifold shared by both cars. Be warned the cheaper non branded sensors cause lots of issues hence we only sell the Bosch version.
Electronic ignition conversion. For points type distributors, fixed or sliding. Negative earth only. Also, available for earlier 23/25D on Negative earth (LU142) or earlier 23/25D with Positive earth (LU142AP12).
ONLY use GCL217 coil for bal...
Also known as the idle air control valve (IACV). Bolts on the side of the injection body housing to control engine idle speed and air flow from cold start up. The blue socket loom cap fits this unit. This is part of MLZ100090. After fitt...
Bluetooth battery charge monitoring system. Compatible with smartphones running IOS, Android or Windows 10. Battery voltage can easily be checked via an app on your smartphone/tablet within bluetooth range.
Step 1
Download...
Sports coil for ballast resistor type ignition.
Best internal parts tested and another intermotor top product.
Its not the name on the outside but whats on the inside which matters.
Original type coil bracket 12G29...
Pop rivet for fixing the headlamp bowl to the wing. Great for MS14 metal bowl but be careful if using on plastic bowls
Pre A plus Electronic Ignition distributor, with vac unit modified to give better performance on any minis with 285/286/296 camshaft profiles
Brand New distributor complete with electronic conversion already fitted.
PRE A PLUS
<...
Pre A Plus Electronic Ignition distributor with vac unit, modified to our specification in the UK to give best performance on any minis with std to 276 camshaft profile.
Brand New distributor complete with electronic conversion already fitt...
rear stop and tail lamp for early BMc cars with red plastic lens.
Also stocked is a white lens and single filament bulb equivalent for use as reverse light on kits cars and Mokes as CHM13REVERSE.
This is the hazard switch repair plug for post 1976 rocker switches, pins supplied so you can wire accordingly.
Lots of things have been written about performance plug ignition wires but regardless of what you believe we all know that good wires are a must. This special competiton wires set from the Lucas factory has 8mm wire and the highest performance, no br...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.