£194.21 exc vat
£233.05 inc vat
In stock
mainly for 1980-1 998cc but used on others.
£194.21 exc vat
£233.05 inc vat
In stockRecommended usage 1 x AN134 to fit one mini.
A plastic lamp spade connection with sidelight bulb aperture for use on sealed beam units only. Uses a GLB501 capless bulb. The mini clubman used sealed beams but had independant side lamps and therefore had an equivalent unit less the s...
This rear loom is for cars with the reverse lamp in the rear lamps and spade type fittings from 1976 on---AN166 has a plug for the rear lamps which fits all new lamps which have a plug attached. With fog lamp.
Also Mini Clubman 1980-83.
Main wiring grommet that fits in the front parcel shelf. ID 12.5mm fits 35mm hole.
Rear body harness with speaker wires, known as thick wall type which was replaced by thin wall PVC covered wire type in 1989. AN169 is the thin wall equivalent and occassionly fitted or found on early cars wothout any problems.
...
We sell about 20 of these per year and many are used on similar models to those indicated-Main and dash loom only--No side wing indicators-indicator stalk on right-alternator-rear lamps with reverse lights-steering lock-inertia starter-centre speedo ...
All Minis require an earth strap from the engine to the body and from 1959-1996
they fitted from the gearbox to the subframe. When they introduced the twin point in 1996 it was moved to the upper engine stabiliser arm. About 13"LONG.
When replacing the 520160A parking switch the inner contact areas on the wiring loom are also worn or damaged so we produced this socket and small length of loom.
Universal post type battery earth strap with clamp type fitting and correct length for most alternatives of batteries fitted.
This is the wiring short conversion loom that fits to the old central speedo and is used by people modifying from 2 or 3 clock dashes to single clock or just repairing damaged looms. With the correct bulb holders and spade fittings. Now uses 5x [link...
A plastic lamp spade connection with sidelight bulb aperture for use on sealed beam units only. Uses a GLB501 capless bulb. The mini clubman used sealed beams but had independant side lamps and therefore had an equivalent unit less the s...
The only battery cable to run the full length of the Mini, this has a positive type terminal that clamps arond the post rather than the helmet or cap type on much earlier cars. Some cars had slightly shorter cables than this but measure your old cabl...
Basically just the rear lamps and number plate lamp wiring loom for mini van.
Large grommet to fit 1"approx holes in bulkhead for items that need to be able to flex and move such as capillary tubes and oil pipes. 7/32" hole size.
The small hole will expand and is also used as wiring loom through bulkhead and battery c...
Plastic holder for the later flasher unit GFU2218. Needs to be mounted to the bulkhead prior to fitting the flasher unit to the holder
Screw for chrome metal number plate lamp on mk3 19790 on - You will have to drill the lens out to take M4 screw.
The half bowl for holding original sealed beams into the headlamp bowl om minis and many other headlamps of the 60s and 70s. Sold singly 2 required per car.
Single bullet connector used to join the front loom to the rear loom near the wiper motor.
Double bullet connector used to join the front loom to the rear loom enar the wiper motor.
These are the screws needed to fix the condenser, points and base plate to 23/25D distributors. See 57H5135 for 45D type distributors.
Electronic Ignition distributor, with vac unit modified to give better performance on any minis with 285/286/296 camshaft profiles
Brand New distributor complete with electronic conversion already fitted.
A PLUS ONLY
Replac...
This chrome over brass wing side repsater lamp rim will fit of the square/oblong lamp lens where fitted on the wing. Fits straight over the original lens and retained by bending the tag. Made in brass to prevent rusting, but also to obtain that deep...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.