CENTRE CLOCK WIRING HARNESS
PM05

£44.00 exc vat

£52.80 inc vat

In stockIn stock
This is the wiring short conversion loom that fits to the old central speedo and is used by people modifying from 2 or 3 clock dashes to single clock or just repairing damaged looms. With the correct bulb holders and spade fittings. Now uses 5x GLB987 and 2X GLB2132 bulbs.

£44.00 exc vat

£52.80 inc vat

In stockIn stock

Recommended usage 1 x PM05 to fit one mini.

Recommended products

Screw type bulbs that fit the plugs (AEU1313A) on the round central clock speedos on all minis from 1959 until the introduction of the non Smiths type plastic clocks as used on the first clubmans and 1275GT. Sold individually.

2.2 WATTS and fits back of gauges in cars with 3 extra 52mm round clocks.

People also bought products

Complete binnacle set for centre speedo cars, kit includes 130 mph electronic black speedo, temperature gauge, oil pressure gauge, binnacle and chrome surround (incl clips). Mini Spares also have a short loom which converts 3 clock Nippon

Se...

Main wiring grommet that fits in the front parcel shelf. ID 12.5mm fits 35mm hole.

Mini Mk 4 998 oval centre dash,twin column stalks,rocker switches including rear fog and heated rear window,reverse lights and rear fog lamp is on headlamp circuit. Intertia starter. To go with AN145 rear loom.

mainly for 1980-1...

Main and dash wiring loom except ECU engine harness for SPI Cooper with no dim dip to SN58746, no alarm --no longer available from Rover.

Engine harness for SPI 1997 onwards Japanese spec cars with manual transmission.

(MPI engine block, SPI injection system, Air con, GCL204 type ignition coil)

Please note where original plugs are no longer available the wires are lef...

This unit fits directly on to the gearbox in place of the standard cable and produces a digital signal for use with any electronic speedometer requiring 12 or 5 volt square wave pulse such as our electronic speedo 13H4443. For pre 1980 s...

Brand new modern electronic version of the classic centre speedo, housed in a billet case with OLED display this unit fits as per original speedos. Features include:



*Trip and total miles

*Remote trip reset

*Driv...

Brand new modern electronic version of the classic centre speedo, housed in a billet case with OLED display this unit fits as per original speedos. Features include:



*Trip and total miles

*Remote trip reset

*Driv...

Mk3 loom for 72-75 saloons with alternator, 2 piece (front and rear).

Fits from 103113 chassis number and has 1 plug to the ecu.

Rear body harness with speaker wires, known as thin wall PVC covered wire type in FROM 1989 and occassionly fitted or found on early cars wothout any problems.



All rear body looms are OBSOLETE from Rover but we can get them made up...

Repair loom and plug for all post 1976 headlamp switches.See PM08 for headlamp switch with plug and correct wires colours for loom repair

Sealing washer for the oil gauge to oil pipe as sold in OL kit and for 21A804 metal pipe to oil gauge.

Complete binnacle set for centre speedo cars, kit includes 200 kph magnolia speedo, temperature gauge, oil pressure gauge, binnacle and chrome surround (incl clips).Mini Spares also have a short loom which converts 3 clock Nippon

Seiko gauge...

Complete binnacle set for centre speedo cars, kit includes 200 kph black speedo, temperature gauge, oil pressure gauge, binnacle and chrome surround (incl clips).Mini Spares also have a short loom which converts 3 clock Nippon

Seiko gauge cl...

Complete binnacle set for centre speedo cars, kit includes 130 mph black speedo, temperature gauge, oil pressure gauge, binnacle and chrome surround (incl clips). Mini Spares also have a short loom which converts 3 clock Nippon

Seiko gauge c...

Front loom only. MK4. Center speedo,inertia starter,rear fog switch.

non ballast coil,last with centre clock

SPI with dim dip-fuel injection cars. Just the main loom only, does not include the engine harness or rear loom. With factory alarm.

Harness to ECU for SPI manual models to chassis number BD 059821 has 2 plugs that connect to the ecu.