£6.99 exc vat
£8.39 inc vat
Out of stock
£6.99 exc vat
£8.39 inc vat
Out of stock
Brake and clutch pedal pads contribute to comfort and safety. They also add that final touch to a nice interior. GPR104 fits brake and clutch pedals of MkI to Mk3 Minis pre 1976 and on the accellerator pedal from 1976 -1996.
Brake and clutch pedal pads contribute to comfort and safety. They also add that final touch to a nice interior. GPR104 fits brake and clutch pedals of MkI & MkII Minis up to 1976 and the throttle pedal on post 1976-1996 models.
Brake or clutch pedal pad for MK4 from 1976 on. In 1990 they improved this pad by introducing SZU10001 which is a far superior product.
Brake and clutch pedal pads contribute to comfort and safety. They also add that final touch to a nice interior. GPR104 fits brake and clutch pedals of MkI to Mk3 Minis pre 1976 and on the accellerator pedal from 1976 -1996.
This switch fits under the brake pedal on the floor. See also BMK1903A locknut for this item.
Special plastic covered clevis pin(first one to appear on a mini) is for the later brake system with servo and intoduced on single point injection.
Brake or clutch pedal pad for MK4 Mini. Will fit any car from 1976 on with the larger brake and clutch pedal. This pad introduced in 1990 was considered a better wearing quality shape and design.
Not often mini owners require the brake/clutch pedal pin but if yours has 110mm shaft and thread length this is the correct one. The metal bushes for the pedals are 2A3034.
White plastic/nylon bush fitted to bellcrank (behind servo in engine bay) on late servo cars. 1988 onwards. 2 required. These can make the brake pedal feel spongey or have too much travel when worn.
Rubber gaiter to keep debris from entering the drum via the backplate handbrake lever SMN10005. Sold singly per backplate, 2 required per car.
Genuine AP Lockheed rubber boot
Set of 4 hoses, 2 front and 2 rear.
Braided brake and clutch hoses have a PTFE inner which helps to eliminate the spongy pedal feel under arduous conditions, and give greater efficiency. The outer braided stainless steel cover e...
Extra high boiling point (above 310°C) brake fluid exceeding the requirements of SAE J1703, SAE J1704 and FMVSS 116 DOT 4 for use in competition braking systems.
Application
Use for racing and high performance br...
Seal for between the brake servo and master cylinder, fits all late 1988 onwards vehicles where the master cylinder was mounted directly to the servo unit.
Replacement rubber grommet for the servo vacuum hose for the 1992 onwards brake servo (GSM119)
NICKEL copper easy bend brake pipe with 2 metric male unions. 22"long, for 1988 on master cylinder lower outlet to PDWA valve outlet nearest to wing-other pipe is HMK026-both for left or right hand drive.
These pipes are retail...
Master Cylinder repair kit for repairing the late GMC90376 master cylinder that was attached to the servo from 1995 until the end of production this kit uses a longer seal in conjunction with a nylon bearing. If your master cylinder has a drill hole ...
Replacement metal master cylinder cap as originally fitted to 1959-1963 Minis on single line brake systems is a great historic feature.
Road use pads but for performance use C-AHT223GREEN these are original size 2.375" which fit later 997 cooper- but if you have the very early small pad type, 2.125" wide for 997cc less split pin holes, these are nearly obsolete you can g...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.