£54.00 exc vat
£64.80 inc vat
In stock
£54.00 exc vat
£64.80 inc vat
In stockRecommended usage 1 x R32026-20 to fit one mini.
Steel ring set, 3 compression ring @ 0.0625" oil ring 0.125 as per original 998 pre A plus and 1098cc versions inc morris minor and sprite range.
This piston for 1098cc engines was designed with 4 rings. The top three compression rings are .0625" thick and the bottom oil ring is .1575" thick.
Pin height in this piston design is 2.2855", this results in a compression of 8.5:1 in most ...
998cc flat top 3 ring circlip type piston set as fitted to early A plus to replace 4 ring set type. Gave 10.3 to1 CR and is a good alternative to use on any 998 with circlip type pistons. Replaced 4 ring(3 ring and scraper) P20754 from Hepolite 1980o...
3mm OIL RING with compression ring size .0591" (1.5mm)and one piece oil ring .1181" (3mm)on p21253 pistons giving 9.7cr on 1275cc. std ring size
For performance see steel ring set with 3 piece oil ring as favoured by engine builders[link]C1...
998cc dished circlip type piston with 4 rings. Compression range of 8.3 to 9:1 depending on block and head but for best performance use later 3 ring flat top piston ADU3490-20. Sold singly,4 per engine required
3 compression ring @ 0.625" oil ring 0.125 as per original 998 pre A plus and 1098cc versions inc morris minor and sprite range.
These rings are +20 oversize with 0.59" compression rings and 0.1181" oil ring fo 998cc
This piston for 1098cc engines was designed with 4 rings. The top three compression rings are .0625" thick and the bottom oil ring is .1575" thick. Pin height in this piston design is 2.2855", this results in a compression of 8.5:1 in most standard ...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
Complete fixing kit for a water pump, includes replacement silicone bypass hose, clips, superseal gasket, replacement bolts and washers.
Mini Spares cam follower with original convex bottom Radii as used by BMC/Rover and made by Clanceys but less the oil hole. Using Clancey drawings and to our design for better cam performance and lift we have made the push rod recess deeper for stabi...
Mineral oil especially formulated for the combined engine and gearbox such as the mini, but for better gearchange etc use MILERS002 except on rebuilt engines where pistons must be allowed to bed in using non synthetic oil. 5 litre bottle.
Se...
Mahle was Vandervell bearings 1.064" 27.05mm wide mains for the late 850cc plus all 997/998/1100cc at 20 thou oversize. Early 850 mains were VP592 and 1.185" 30.10mm wide...Quantity required-1 set.
Lower Stabilizer Kit, RH.
Designed as an almost mandatory addition to any Mini with a rod change transmission, extra stabilizers will greatly aid any car. In stock form the control is left to the upper stabilizer. This often results in not o...
Mahle was Vandervell bearings 1.064" 27.05mm wide mains for the late 850cc plus all 997/998/1100cc at 10 thou oversize. Early 850 mains were VP592 and 1.185" 30.10mm wide.
Mahle was Vandervell bearings 1.064" 27.05mm wide mains for the late 850cc plus all 997/998/1100cc at standard size. Early 850 mains were VP592 and 1.185" 30.10mm wide..Quantity required-1 set.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.