NUMBER PLATE LAMP HOUSING IN CHROME - MK3 ON
8B12501METAL

($16.56) £16.56 exc vat

($19.87) £19.87 inc vat

In stockIn stock
Owing to their position on the car and chrome on metal these must be cleaned weekly. They are a direct replacement for MK3 on original number plate lamps and are less the 2 light lens, which are the same fitting for this lamp. These lamps use M4 scre...

($16.56) £16.56 exc vat

($19.87) £19.87 inc vat

In stockIn stock

Recommended usage 1 x 8B12501METAL to fit one mini.
Rear and Interior lighting - Qty 1

Recommended products

Screw that holds on the exterior plastic type mirrors to the door, plus the handbrake fairlead guides on the floor of the car - also holds air vent nozzles to dash. 3/16" unf 3/4" long including head - for plain washer see WA1090.

Two of these plastic lens that hold festoon bulbs (GLB239) are mounted in the metal cast number plate housing (13H6900) on all MK3 bootlids from 1970on. Sold individually with bulb LESS FIXING SCREWS.

See PMZ206 for screw replac...

Screw for chrome metal number plate lamp on mk3 19790 on - You will have to drill the lens out to take M4 screw.

Alternative products

All Mk3 saloons from 1970 to the cars demise in 2002 had the number plate lamp mounted in this housing on the bootlid and colour matched to late car.

These housings are supplied bare metal so need painting to colour required.

This...

People also bought products

Boot hinge gaskets and fittings for original type hinges

rear stop and tail lamp for early BMc cars with red plastic lens.

Also stocked is a white lens and single filament bulb equivalent for use as reverse light on kits cars and Mokes as CHM13REVERSE.

Screw for chrome metal number plate lamp on mk3 19790 on - You will have to drill the lens out to take M4 screw.

Stainless steel screw kit for all mk2/3 lens to lamp body. Comes as a car set with six screws and six fibre washers.

Lucas upper lens plus gaskets for cars with built in reverse facilty in lamp

These are the upper lens in clear plastic with 2 new lens gaskets to stop water seeping into the lamps, plus the correct bulbs when you require the fashionable clea...

This fog lamp unit comes with a SEPERATE XFU10002 bracket for R/H fitting only, see XFE1007 for LEFT HAND FITTING SUCH AS L/H/D,

See XFE10006 for lamp only

New lenses do a lot to improve the looks of a car, and may make it more visible. To make sure that they match we recommend that you replace both lenses together.

Kit includes 2 original rear lower lens in white with reflectors plus 2 upper lens in white for the modern day look. Included are the 4 bulbs required to make the kit legal.

The lens seals are available individually as XFH100460...

Lucas clear upper lens for cars with reverse lamp built in rear lamp

with correct bulbs for the fashionable clear rear lens look. If you want to replace the lower clear lens with the red reflector because they are faded or damaged use kit MS...

Genuine L/H lamp.Beware of cheaper inferior lamps for sale.

Fitted from 1976 on as standard equipment this was the Lucas style lamp with the built in reverse lamp.Supplied with gaskets. Many people now change the upper lens to the more fash...

Convert your upper lens to all white but dont forget to use correct colour bulbs

for all lamps that have a built in reverse lamp.

Genuine R/H lamp. Beware of cheaper inferior lamps for sale.Fitted from 1976 on as standard equipment this was the Lucas style lamp with the built in reverse lamp. Supplied with gaskets. Many people now change the upper lens to the more fashionable w...

For MK2/3 lamps without built in reverse lights these are the rubber seals between the lamp base and the car body, this is left hand.

Two of these plastic lens that hold festoon bulbs (GLB239) are mounted in the metal cast number plate housing (13H6900) on all MK3 bootlids from 1970on. Sold individually with bulb LESS FIXING SCREWS.

See PMZ206 for screw replac...

This is the boot seal that actually fits on the car body which saved drilling holes in the bootlid. Fitted from about 1988 on.

These gaskets should be changed when replacing the hinges, this one goes between the bootlid hinge on the body, see 24A2175 also for upper on bootlid.

These gaskets should be changed when replacing the hinges-this one goes between the bootlid hinge on the bootlid. See also 24A2176 for gasket on body.