£17.60 exc vat
£21.12 inc vat
In stock
These housings are supplied bare metal so need painting to colour required.
This housing holds the 2 number plate lights PRC1230A which are sold individually.
£17.60 exc vat
£21.12 inc vat
In stockRecommended usage 1 x 13H6900 to fit one mini.
All mk3 cars had the number plate on the boot lid and this is the rubber seal to go between the lamp and bootlid.
Two of these plastic lens that hold festoon bulbs (GLB239) are mounted in the metal cast number plate housing (13H6900) on all MK3 bootlids from 1970on. Sold individually with bulb LESS FIXING SCREWS.
See PMZ206 for screw replac...
Screw for holding PRC1230A to the number plate light body, 1970 onwards.
Owing to their position on the car and chrome on metal these must be cleaned weekly. They are a direct replacement for MK3 on original number plate lamps and are less the 2 light lens, which are the same fitting for this lamp. These lamps use M4 scre...
Tank strap bracket welded to the rear of the boot floor which the single diagonal tank strap 21A2838 attaches to.
Key barrel set for Mk3 onwards door handles and boot handles.
This very heavy duty bonnet strap is a excellent reproduction of the original factory Special Tuning department special. A copy of our Tan leather strap, but now available in black.
3.3mm thick from the tanneries for use on horse bridles,wit...
Full carpet boot liner kit, completely lines the inside of the boot area.
Not suitable for MPI minis.
Full carpet boot liner kit, completely lines the inside of the boot area.
Not suitable for MPI minis.
Threaded boss that fits in the floor of MK1 minis for the spare wheel clamp 14A6511 to screw into.
Round spare wheel clamp with bolt for fitting in the boot to the spare wheel boss as fitted to Mk1 minis. See 88G479 for the boot floor boss that this clamp screws into.
Used on all MK1/2/3 bootlids there are 26 little holes drilled around the inner edge to hold the seal on and this kit contains the 26 clips. For single clips see 14A6585. Later cars 1988 on fitted a seal to the body only. (CKE10018)
Full Mk1 door handle set with 2 front door locking handles and boot handle with matching keys.
MKI boot lid manufactured by British Motor Heritage. Always fix your swinging number plate and hinges on for dummy fit and alignment before spraying.
The double skin Mk1/2 type 8G9270 introduced in december 1966 is only availabl...
If you want to hold it in place then this is easy and simple. 4" long rubber hooks can be used on bonnet and/or boot lid. Packaged in pairs with both brackets.
Not just a skin, but a complete MK3 shape boot lid with inner skin. Designed for race use, some finishing will be required.
A complete set of 2 front door and one boot handle in chrome all with the same key numbers for wind up window door minis 1970on (keys included).
Door Handle Gasket's should also be replaced at same time, CZH1729 and [link]ALA579...
This is the boot seal that actually fits on the car body which saved drilling holes in the bootlid. Fitted from about 1988 on.
This kit contains all the brackets and mounts that were fitted on to the floor on original Coopers, Wolseley Hornet and Riley Elf with boot boards fitted as standard.
This kit does not include the bracket on the boot board 14A9783
These gaskets should be changed when replacing the hinges, this one goes between the bootlid hinge on the body, see 24A2175 also for upper on bootlid.
These gaskets should be changed when replacing the hinges-this one goes between the bootlid hinge on the bootlid. See also 24A2176 for gasket on body.
Non Genuine metal battery box. always going rusty owing to the location of where it is fitted. Requires welding in place and preferably painted or a protective coat. Remember to check if the battery cover, strap and clips need changing. Popular afte...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.