($191.81) £191.81 exc vat
($230.17) £230.17 inc vat
In stock
($191.81) £191.81 exc vat
($230.17) £230.17 inc vat
In stockRecommended usage 1 x AN111C to fit one mini.
You should always use this kit for fitting any auxiliary spot or fog lamps.
Kit contains wiring and safety relay-cheaper than a burnt out engine compartment.
Please note, SPI and MPI cars have this facility built as standard safety ...
All Minis require an earth strap from the engine to the body and from 1959-1996
they fitted from the gearbox to the subframe. When they introduced the twin point in 1996 it was moved to the upper engine stabiliser arm. About 13"LONG.
This is the wiring short conversion loom that fits to the old central speedo and is used by people modifying from 2 or 3 clock dashes to single clock or just repairing damaged looms. With the correct bulb holders and spade fittings. Now uses 5x [link...
A plastic lamp spade connection with sidelight bulb aperture for use on sealed beam units only. Uses a GLB501 capless bulb. The mini clubman used sealed beams but had independant side lamps and therefore had an equivalent unit less the s...
Large grommet to fit 1"approx holes in bulkhead for items that need to be able to flex and move such as capillary tubes and oil pipes. 7/32" hole size.
The small hole will expand and is also used as wiring loom through bulkhead and battery c...
Wiper Swithch MK1/2/EARLY MK3 blade type switch for using to convert to 2 speed wipers when current 2 speed wiper motor is used.
Negative earth A Plus 59D for any 1275cc with vac unit with modern day driving curves and petrol avaiable.
For best performance and tune we advise our electronic evolution version C-27H7701
Distributors can 'work' lon...
Resistor for AFU3389LED and AFU3389WLED, this is needed to enable the lamps to function properly. Sold in pairs.
Screw for holding PRC1230A to the number plate light body, 1970 onwards.
Stainless steel screw kit for all mk2/3 lens to lamp body. Comes as a car set with six screws and six fibre washers.
Double bullet connector used to join the front loom to the rear loom enar the wiper motor.
These are the screws needed to fix the condensor, points, base plate and vacuum to 45D and 59D distributors. For 23/25D type see 17H5106
Foam gasket that goes between the indicator/side lamp unit and front panel for all clubman models
A Plus Electronic Ignition distributor with vac unit, modified to our spec in UK to give best performance on any minis with std to 276 camshaft profile.
Ideal for our EVOLUTION001 camshaft
Brand New distributor complet...
Replacement distributor cap retaining clip for all 45D type distributors-sold per clip.
THE LENS FIXING SCREWS FOR THE REAR LENS ON MK4 1976 ON WITH REVERSE LENS ARE ALL THE SAME. SOLD INDIVIDUALLY. ALSO FITS TWIN POINT FRONT INDICATOR LAMP.
3 per lamp required or 6 per car set.
Courtesy switch for MPI minis from 1996 when the wiring was changed from bullet type to spade connection. This is the switch that fitted into the A post to turn the interior light on and off, the earlier switch is no longer available so if you have a...
Lucas upper lens plus gaskets for cars with built in reverse facilty in lamp
These are the upper lens in clear plastic with 2 new lens gaskets to stop water seeping into the lamps, plus the correct bulbs when you require the fashionable clea...
gasket between lens and lamp unit on Clubman front lamp
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.