($83.39) £83.39 exc vat
($100.07) £100.07 inc vat
In stock
($83.39) £83.39 exc vat
($100.07) £100.07 inc vat
In stockRecommended usage 1 x C-AEG372 to fit one mini.
LONG CENTRE BRANCH EXHAUST MANIFOLD FOR FUEL INJECTED CARS WITH A SENSOR TAKE OFF in main LCB body, THIS IS FOR USE WHEN THE CATALYST IS BEING REMOVED AND A RC40 EXHAUST IS BEING FITTED. If the catalyst is to be retained use [link]C-AEG3...
Exhaust manifold to downpipe clamp. For 32mm o/d pipe size.
The key to eliminating exhaust leaks at the manifold flange is the clamp. These cast clamps are the best style to use. A real piece of kit to use eradicating a multitude of likely p...
This is the clamp on the cooper freeflow manifold to clamp it to the engine for extra support, supplied with tag.
Standard bore road LCB (1-3/4"id) that has an enlarged and reshaped middle pipe which creates a type of vortex, simulating a pulsing effect similar to the outside two pipes,thus producing an improved BHP,Torque and power curve.Ideal for very hot smal...
Special reinforced gasket for injection cars has metal inserts on exhaust ports plus a metal back on the manifold side which makes surface easier to clean when replacing. Often used on Turbo cars when correct gasket is in short supply.
...
Exhaust manifold to downpipe clamp.
The key to eliminating exhaust leaks at the manifold flange is the clamp. These new clamps include proper brass nuts and support washers. Fits most 850cc, 948cc, 998 etc. Those engines with single carb an...
Special tin plate type of gasket that goes between the manifold and exhaust downpipes on all injection cars.
Smarten up your engine bay with these stainless steel nuts which are not only stronger and resistant to rust but the multi point nut heads are easier for access. See also kit C-STR287.
This short pipe fits on the end of our freeflow manifols C-STR816 to give the overall length of an LCB when you have an exhaust system to fit that was made explicitly for LCB fitment.Total length is 300mm ID is 44mm OD is 48mm.
Manifold gasket fitted to all A series pre 1992 except Turbo which had a reinforced exhaust ports GUG704063MG and SPI from 199. From 1991 on a new better gasket with reinforced exhaust ports and backing was fitted GUG704053MG
Link pipe for fitting between the LCB and the catalyst. It has a stainless steel knuckle joint to prolong life and give the flexibility required on the system to overcome damage. See also alternative RC40-016
Y piece replacemen...
Special length and thread pattern only for the exhaust manifold to downpipe of injection cars, see also FX108047 special nuts. Metric M8.
The newest development in the A-series engine is the use of these nuts with swedged-on washers. The washer will not separate from the nut, so you won't lose it. Yet the nut rotates independently while you tighten it. What a great idea.
1.75" Bore centre exit twin tail pipe maniflow rear box with adaptor to sleeve down to the standard mini 998cc type exhaust system.
The long wheel base of the Mini Van, Wagon and Pick-up means the popular RC-40 exhaust comes up a little short! This system from Maniflow (pipes, resonator and muffler), is made for the long bodies. Just because you have a utility vehicle it does no...
This 5/8unf steel hexagonal head blanking plug was made for the inlet manifolds where the servo union can be fitted, plus blanking off the thermal transmitter hole under the thermostat. Uses 1B3664 washer ----------please note this will ...
Genuine mini Spares inlet manifold dyno tested and designed for our Stage one kit C-STN17. The single SU manifolds is developed to give maximum airflow and gas speed, yet fit all engines even if the standard air cleaner set-up is used. I...
Standard larger 1.750" bore twin box exhaust system for saloons.
see C-ARA339 for van and pickups.
Also known as stepping motor--idle air control valve (IACV)
Bolts on the side of the injection body housing to control engine idle speed
and air flow from cold start up.The blue socket loom cap fits this unit
THIS IS A MOD...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.