£146.28 exc vat
£175.54 inc vat
In stock
£146.28 exc vat
£175.54 inc vat
In stockRecommended usage 1 x C-ARA339 to fit one mini.
Complete mounting kit for the RC40 exhaust. Includes all new rubber mounts, brackets and clamps.
1.75" bore twin box, centre exit exhaust system. This exhaust system by Maniflow is straighter and louder than the RC-40. Very high quality with a skid plate on the bottom of the muffler and a polished stainless tip.
Not road legal except for turbos this is a 2" bore single box system. Side exit
and for twin box see C-ARA334
For all cars with a catalyst--this section fits from the catalyst back and has 2 silencer boxes.1.75" bore
Standard larger 1.750" bore twin box exhaust system for saloons.
see C-ARA339 for van and pickups.
2.75" long steel intake manifold by Maniflow for Weber 45 DCOE/DHLA.
Stainless steel version of C-AEG376. Standard bore road LCB (1-3/4"id) that has an enlarged and reshaped middle pipe which creates a type of vortex,simulating a pulsing effect similar to the outside two pipes,thus producing an improved B...
Standard bore road LCB (1-3/4"id) that has an enlarged and reshaped middle pipe which creates a type of vortex, simulating a pulsing effect similar to the outside two pipes,thus producing an improved BHP,Torque and power curve.Ideal for very hot smal...
Standard bore LCB (1-3/4"id) that is ideal for very hot small bore engines, for standard to high performance 1275s and for street 1380s.
There is NOT enough clearance room when fitting to old cars with rubber couplings which foul. Using [lin...
LONG CENTRE BRANCH EXHAUST MANIFOLD FOR FUEL INJECTED CARS WITH A SENSOR TAKE OFF in main LCB body, THIS IS FOR USE WHEN THE CATALYST IS BEING REMOVED AND A RC40 EXHAUST IS BEING FITTED. If the catalyst is to be retained use [link]C-AEG3...
Maniflow's tubular reproduction of the original Cooper 997/998cc exhaust manifold manufactured out of the same tubing as the STD bore LCB. This free flow manifold works vey well at lower speed pick up, the LCB is noisier but better at the top end of ...
Standard bore LCB (inch and three quarters internal diameter) for post 1990 cars with catalyst that is ideal for for standard to high performance 1275s and for street 1380s. The best quality production manifold is made by Maniflow. The Long Centre B...
Stainless steel Standard bore LCB (1-3/4"id) that is ideal for very hot small bore engines, for standard to high performance 1275s, and for street 1380s. And in stainless steel for long life!
There is NOT enough clearance room when fitti...
Basically the C-AEG373 LCB exhaust manifold but with a link pipe for retaining the catalyst on carb models after 1990-92.
Exhaust manifold to downpipe clamp. For 32mm o/d pipe size.
The key to eliminating exhaust leaks at the manifold flange is the clamp. These cast clamps are the best style to use. A real piece of kit to use eradicating a multitude of likely p...
The very rear bobbin type mounting rubber on every mini made until the introduction of a rubber hanger strap in 1992. When the RC40 or similar systems are fitted, 2 will be required. This is a stronger poly version.
Rear RC-40 twin box system to fit catalyst for cars built late 1991 on SPI(not early carb coopers). It has the hanger rods fited for mounting onto the rubber type straps. This makes it a twin box system with a little throatier pleasing note, but a mu...
Stainless steel tailpipe trim with hanger bracket designed for fitting to the tailpipe of RC40 rear box as an extension piece. This is part of our RC40PACKAGE015 kit for Van/Estate and Pickup exhaust system when a freeflow o...
Blanking plug to blank of the Lambda sensor hole on all SPI/MPI models.
M10 metric flanged bolt 35mm long for catalytic converter. (4 required per unit)
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.