($12.00) £12.00 exc vat
($14.40) £14.40 inc vat
In stock
($12.00) £12.00 exc vat
($14.40) £14.40 inc vat
In stockRecommended usage 1 x C-AEG393 to fit one mini.
Goes on both ends of the rocker shaft to keep tension on the #1 & #8 rockers.
Spring seat shims (set of 4), 0.020" thick (0.5mm).
Spacer shims to increase valve seat pressure and overall spring rate.
These were also used on all the 8 port head valve seats to prtect the alloy seats from wear. (8 port now C-AHT...
Spring seat shims (set of 4), 0.040" thick (1mm).
Spacer shims to increase valve seat pressure and overall spring rate.
These were also used on all the 8 port head valve seats to prtect the alloy seats from wear. (8 port now C-AHT36...
Alloy CNC version of the cylinder head take off 12G2534. The standard item being steel can be prone to corrosion, this CNC alloy version is smart, and will not corrode like steel does
Genuine version of the thermostat gasket for all A series. Black one side and red the other they are fitted black side to the head. Green to the thermostat.
We have no evidence as yet that they last longer but do look good.
See [lin...
Spacers for under the rocker pedestals are used mainly by engine tuners to allow tappet adjustment to be made where cylinder head mods have been carried out. 1.3mm/0.0512" thick, this can be used to hold locating screw on rocker post assembly but the...
Small brass tapered plug fits 1/4" hole for the oil release passage PRE 1985 on Metro blocks which most engine tuners replace to clean out any sludge - 6.95mm tapering down to 6.25mm - also used as a general engine plug but mostly as a cylinder head ...
Larger bore thermostat housing, approx 32MM wide(1.250")and has a small outlet pipe which is blanked off (not drilled out). This same housing was used on Metros but the blanked off outlet was drilled out for water to go to the expansion tank. Therefo...
Upgraded rocker cover gasket made in silicon, cut outs for 11 stud head and ideal when rocker cover is removed on a regular basis.
Rarely you may require longer rocker cover bolts when fitting this so use CAM6823.
Sold individually.
To help rocker pad to valve stem alignment and reduce friction, the standard springs can be replaced with solid spacers and correctb shim set. The spacers and shim kit are sold as C-AEG392.
Mini cork Rocker cover gasket, suitable for all Minis and A series engines except those with 11 stud heads (see part number GUG5038VC). A must have replacement item when adjusting rocker clearances. see GUGG705009EVO for sil...
This 5/8unf steel hexagonal head blanking plug was made for the inlet manifolds where the servo union can be fitted, plus blanking off the thermal transmitter hole under the thermostat. Uses 1B3664 washer ----------please note this will ...
Payen,stamped BK450, original standard composite reinforced gasket used on all large bore engines by Rover including Metro and MG Turbo and is an exceptionally good gasket.
Asbestos free with copper type sealing rings. Compressed volume is ...
Probably the most changed stud on the mini. This is the length used on every A series engine until the introduction of the sandwich plate when longer ones were required. A stainless steel variety C-STR286 is available which we do recomme...
No reason for an oil leak here. For the price, they should be replaced every time the rocker cover is off. Sold singly, 2 required per engine.
We have now sold all the original seals we cleared out from Rover so July 2017 retooled to make a ...
Mini Spares spacer kit re-designed in 2005 for correcting rocker alignment.
This kit has been produced to help rocker pad and valve stem alignment plus reducing friction. The standard springs can be replaced with this special kit of 3 spacer...
11/16" dowty seal for post 1991 cars where the original pipe has been replaced with a braided pipe or an oil cooler has been fitted using part number MOC4. used on the TCZ102
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.