CARBURETTOR WEBER 45DCOE
C-AHT143

($532.50) £532.50 exc vat

($639.00) £639.00 inc vat

In stockIn stock
Genuine Weber 45DCOE Carb, calibration from the factory is as below:





Choke 36

Throttle Plate Angle 78 degrees

Auxiliary Venturi 4.5

Needle Valve 200

Main Jet 145 Pump Jet 45...

($532.50) £532.50 exc vat

($639.00) £639.00 inc vat

In stockIn stock

Recommended usage 1 x C-AHT143 to fit one mini.

Recommended products
WEBER LINKAGE KIT
C-AHT145

Weber DCOE twin cable linkage set top mount.



Fits on top of single or twin DCOE installations to provide a professional throttle linkage solution.



Supplied with 2 x throttle cables and associated pedal mounting h...

($144.00) £144.00 exc vat

($172.80) £172.80 inc vat
People also bought products
HOSE CLIP 8-12MM
GHC108012

Small hose clip for 1/4" fuel line (our part number PETROLPIPE)

($1.16) £1.16 exc vat

($1.39) £1.39 inc vat
CARB HIF38 REBUILD KIT
CRK274

For HIF38 carbs,this is the full rebuild kit with the spindle and throttle disc and bushes--- see CSK94 for service kit

($92.88) £92.88 exc vat

($111.46) £111.46 inc vat
CARB BUTTERFLY ANTISTALL HS4 WAXSTAT JET TYPE
WZX1324

plain butterfly with small hole at bottom for HS4 waxstat jet type carb and uses WZX177 spindle-or see kit full rebuild kit CRK121. This is usually fitted to FZX3013 replacement carb --same size butterfly on all...

($17.24) £17.24 exc vat

($20.69) £20.69 inc vat
SPINDLE KIT HS4 1.5"
WZX1177

throttle spindle kit for single HS4 type carbs-.Quantity required-1 kit. -the butterfly is available seperately as WZX1323 for plain-WXZ1325 with air valve

($13.50) £13.50 exc vat

($16.20) £16.20 inc vat
CARB SPINDLE KIT 1.1/4" HS2
WZX1310

spindle and fixings only for the HS2 carb-the butterfly for this is WZX1320.

sorry folks but buying both kits you get double the gaskets

($11.70) £11.70 exc vat

($14.04) £14.04 inc vat
CARB BUTTERFLY KIT 1.25 HS2
WZX1320

The butterfly kit for HS2 carbs and the spindle kit is WZX1310

($15.99) £15.99 exc vat

($19.19) £19.19 inc vat
22" BRAIDED PETROL PIPE 1/4" BORE
PPK7

Before the days of Aeroquip, Minis were fitted with braided steel rubber fuel lines. They should be used in place of rubber for all fuel lines in the engine compartment. They come made to length, with rubber end caps. 1/4" bore size.

This is...

($7.30) £7.30 exc vat

($8.76) £8.76 inc vat
FLOAT NEEDLE VALVE HS2/4/6 (VITON TIPPED)
WZX1100A

This is the original type of needle valve that governs the plastic fuel float in your SU carb.

An alternative better upgraded version is available as CA90.

($10.38) £10.38 exc vat

($12.46) £12.46 inc vat
ACCELERATOR CABLE NYLON SLEEVED EXTRA LONG
C-AHT85

Our heavy duty throttle cable is superior in many ways.

A nylon interior ensures smooth operation. The outer cable is 32mm longer and inner is 95mm longer than the standard one.

Cable to carb bolt is ACC5062.

($6.10) £6.10 exc vat

($7.32) £7.32 inc vat
HEATER AND CHOKE CABLE CLIP HIF CARB
CZK6491

Clip on the heater valve for heater cables on vehicles from 1990 where the in line remote heater valve was used. It has also been used as a clip for HIF carbs to hold the cable but the one from Rover is 13H3472.

($1.35) £1.35 exc vat

($1.62) £1.62 inc vat
NEEDLE AAA SWINGING TYPE
CUD1000

A very usefull tuning needle for single and twin carbs when camshaft change for carbs with floating needles.

($8.25) £8.25 exc vat

($9.90) £9.90 inc vat
FLOAT SPINDLE HIF
CUD2082

spindle to hold the float to the float lid on the bottom of HIF carbs only.

the float is WZX1509A and needle valve is WZX1099A except turbo which is WZX1095

($4.93) £4.93 exc vat

($5.92) £5.92 inc vat
FULL HS2 TWIN REBUILD KIT
CRK101

Master carb rebuild kit

Twin 1 1/4" SU carbs were stock on Cooper S and most Spridgets and are popular upgrades on many cars. The reason they are so popular is that the design is fantastic- but let's face it people; everything wears out and...

($126.03) £126.03 exc vat

($151.24) £151.24 inc vat
CARB JET HS4 MINI TYPE RED
AUD9451A

Original type jet with red plastic end for HS4 carbs---If you have the later nylon coated jet see part number LZX1111A.

($12.00) £12.00 exc vat

($14.40) £14.40 inc vat
MANIFOLD INLET WEBER 45 DCOE 3.5" MANIFLOW STEEL
C-AHT777

3.5" long steel intake manifold by Maniflow for Weber 45 DCOE/DHLA.

($170.13) £170.13 exc vat

($204.16) £204.16 inc vat
CARB HS4 WAXSTAT TYPE SERVICE KIT
CSK65

For HS4 single carbs this is the very least of the parts required for an overhaul kit. If you require the spindle and disc and bushes see CRK121.

Pre waxstat with the red jet is CRK227.

($83.91) £83.91 exc vat

($100.69) £100.69 inc vat
GASKET 1.25" HS2 CARB (GUG705831GM)
1G2624B

Manifold to carb gasket for HS2 single and twin carbs, usually 3 per carb required.

($0.47) £0.47 exc vat

($0.56) £0.56 inc vat
CARB HS2 SPINDLE REPAIR BUSH
AUD3079

Worn throttle spindles cause erratic performance from your carb and sometimes the housing gets worn--These are the bushes to repair worn carbs when replacing spindles for HS2 carbs. As a guidline 0.250" internal diameter and ream carb bo...

($4.16) £4.16 exc vat

($4.99) £4.99 inc vat
MANIFOLD LOCATING RING
12G297

Locating rings originally made for 12G295 heads with twin carbs to line up the inlet manifold to the inlet ports on the cylinder head it found its way on most twin carb factory produced cars. There is a recess in the inlet port on the he...

($2.56) £2.56 exc vat

($3.07) £3.07 inc vat
CARBURETTOR LEVER PIN
ACC5062

Pin to hold the accelerator cable which locates in the carb bracket lever. Supplied as originally fitted with washers, nut and split pin plus a proper machined hole for the cable unlike many others on the market- which come either bare or with wrong ...

($2.93) £2.93 exc vat

($3.52) £3.52 inc vat