ARP MAINS NUT SET - COOPER S ONLY
C-AJJ4013

($27.00) £27.00 exc vat

($32.40) £32.40 inc vat

In stockIn stock
Special "S" main bearings nut set (6).7/16"AF thread

On all performance A series engines it is essential to ensure accurate and as near permanent location of the centre main bearing of the crankshaft as possible. Flexing allowed here, especi...

($27.00) £27.00 exc vat

($32.40) £32.40 inc vat

In stockIn stock

Recommended usage 1 x C-AJJ4013 to fit one mini.
Block Components & Pistons - Qty 1

Recommended products

These are made by ARP in the USA and considered the best available. This nut and bolt set also fit Sprite and Midget in line engines. Quantity required one kit per car. Torque up to 40-42lb ft.

Mini Spares own Universal gasket set.

This engine block gasket set fits all manual blocks and include rubber tappet chest covers and bolt seals, also including A plus and Pre A Plus timing gear and cover gaskets. For the equivalent gasket se...

People also bought products

Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).

Complete nut, bolt and washer set for engine to gearbox only

Water pump fitting kit for models without bypass facility, includes new bolts, washers and superseal gasket.

Complete fixing kit for a water pump, includes replacement silicone bypass hose, clips, superseal gasket, replacement bolts and washers.

later cars used this bolt to hold on the spin on filter head to the block-earlier cars used the CHS2613 stud--both are interchangeable

3/8"unc 1"long

A series mini engine crank pulley bolts have been known to come loose, caused by pulley damper vibration on competition engines. This is a high tensile longer extended thread cap head bolt with thick washer to rectify this problem and also allow furt...

Longer main bolt stud.

As supplied with our main strap kit.

The high tensile bolts supplied with the 998 centre main strap kit.

You require 5 of these high tensile short head studs and they torque to 42lb/ft. See also complete kit which includes these top grade studs C-AHT279. 3/8"unc stud with unf end for head nut and is 4" long. See other long head stud [link]C...

Fits all current range of oil pumps including GLP110MS.

Holds C-AHT54 oil pick up or standard oil pipe to case on outside of gearbox case 1/4"unf bolt 1.625"long

3 lengths of oil pump bolts have been used s...

Special bolt that fits the engine front plate to support the adjusting link for alternators/dynamo

The special washer under the tappet cover bolt.Sold singly 2 required per engine.

See 12A1176 for seal

1.75" LONG shouldered 1/4" bolt fits original concentric pumps plus some GLP139 and GLP110MS - check that you need a bolt this length as many later pumps require shorter bolts. This can of course be cut down or see [link]BH6...

Using new hardware makes any job more pleasant. If you're servicing your cylinder head you should examine the rocker studs for signs of stretching or stripped threads. Two long (51K885) and two short (51K1473) per head.

This is ...

This A type block 3/8" unc

stud to retain the cylinder head is 11/16"(17.3mm) longer than the standard 4" type with 1.5" of thread to hold brackets for other ancillaries such as coil. Usually fitted only at the heater tap end of the cylinde...

Engine stabiliser arm to block bolt. This is the longer bolt that fits the engine stabiliser rod to the cylinder block.

The 8 port head is taller than standard A series heads so these MGB short head studs are used on the front--4 3/8" long 3/8" UNC stud with unf end for head nut. These studs are also used for rod change gearbox differential housings.

[link}53...

Fitted to the rear of engine blocks to drain out water these are now obsolete from Rover but available from us.1/4"bsp

This alternative multi point nut was preferred by racers because the plastic locking part of the original AEG147 could fall out under extreme conditions on an over hot running engine. Current AEG147 are now an all metal nut ...