($691.97) £691.97 exc vat
($830.36) £830.36 inc vat
In stock
($691.97) £691.97 exc vat
($830.36) £830.36 inc vat
In stockRecommended usage 1 x C-AJJ4028D to fit one mini.
Genuine AP car set of 4 brake hose for cars with front disc brakes. If you are changing one through wear and tear it is a good idea to change the whole set and save money with peace of mind about your brake system. Securing nuts included
UK made-Rear brake drum on all post 1984 cars plus the Mini Cooper "S" 1275GT models which has a built in spacer ( 1") and uses standard 1 1/4" shoes (GBS834AF). It will also fit the front or rear of a non-S Mini, with 1 1/4" shoes or (1 1/2" shoes G...
Set of 4 hoses, 2 front and 2 rear.
Braided brake and clutch hoses have a PTFE inner which helps to eliminate the spongy pedal feel under arduous conditions, and give greater efficiency. The outer braided stainless steel cover e...
These copper sealing washers should be replaced every time the hoses are undone as a precaution. 10mm i/d, 15mm o/d. is smaller than a 3H550
Original genuine sintered split washer for behind the hub nut that goes on the cv joint drive flange.
This is not the cheap old metal type often sold by our competitors which Rover discontinued and changed to sintered for all production car...
Countersunk crosshead screw. 1/4"unf / 16mm(3/8") total length.
To hold the drive flange to the brake disc on the Cooper S type 7.5" wide brake set up. Also holds striker plate for door.
Mini Spares own stamped GCV1013. Brand new CV Joints with gaiter, hub nut, grease and clips. Stamped with our part number GCV1013 for identification from may 2014 to denote our authenticity of this top quality joint, sold singly.
These are t...
Locktabs for under the steering arm bolts on all minis. Fits either side.
Sold individually
High tensile 3/8" bolt 1.3125" long, to hold the standard calipers to the hub on disc brake models. Correct length shank and material. T grade 62 ton rating with vickers 287 reading-25-32 rockwell. The ERA turbo used Metro 4 pot calipers and used spe...
Genuine Minispares approved joints that we have supplied since 2004-
Beware of spurious products on the market as these are a safety critical part.
BEWARE OF CURRENT SO CALLED GENUINE ITEMS AS THEY ARE NOT FIT FOR PURPOSE.
...
Minispares own product-R/H to last Rover drawings and supplied to us by a UK Heritage specialist. Originally the BMC castings were machined by Portland Eng but in the 90's we put down tooling with IVRA in Italy who had them manufactured by Torme in I...
Genuine AP L/H caliper-Whether you are upgrading from the smaller 997/998 discs to the larger 'S' brakes or simply restoring a Cooper S, you'll appreciate the value of these brand new brake calipers. See 27H4657MS for our own product.
Mini Spares standard road use disc 7.5" wide using material GG25EURO.
These were standard fitment on all Cooper S models plus early 1275GT made from OE drawings to the correct material spec. Cheaper types on the market that we have tried sin...
Brake hose for models with disc brakes.Beware of very cheap imports. We all believe that our life often depends on our braking system. But how can you tell when "it's good enough"? The flexible rubber brake hoses are a prime area for concern. The ho...
Always check these grease nipples on your front hubs are working as they are very important. These two swivel pin grease nipples are the same, upper and lower. Also used on the rear radius arms. Sold individually.
these are top quality greas...
Mini Spares own quality product from original drawings in EN24 material for 7.5" wide disc set ups.
The Mini Cooper "S" drive flange as used on all 7.5" disc Cooper S/1275GT variants was originally intended to use 10" wheels as an integral p...
Genuine AP R/H caliper. Whether you are upgrading from the smaller 997/998 discs to the larger 'S' brakes or simply restoring a Cooper S, you'll appreciate the value of these brand new brake calipers. See also 27H4656MS for our own Mini ...
Cheaper alternative to genuine timken front bearing kits.
These are very well tried and the best of any of non genuine bearings available.
Sold as one hub kit only. Please note-for arduous or race use Timken bearings in genuine GHK1...
Correct size and length brake pad pin for the caliper using 7.5" disc size as fitted to Cooper S and 1275GT. 4 required for 1 car, also fits Cooper 7" calipers. 3mm diameter.
Minispares own product-L/H, to last Rover drawings and supplied to us by a UK Heritage specialist. Originally the BMC castings were machined by Portland Engineering but in the 90's we put down tooling with IVRA/Italy who had them manufactured by Torm...
Our favourite pads as the give less brake pad dust which destroys alloy wheels.
Very durable and great for most road usage. The green upgrade for fast street is C-8G8995GREEN.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.