MINI VERTO CLUTCH KIT FOR INJECTION MODELS
CK9378

($85.50) £85.50 exc vat

($102.60) £102.60 inc vat

In stockIn stock
Non Genuine 3 piece Injection Clutch with the larger 190mm wide for 1990 on and all injection cars, but it can be used on earlier non injection Verto type engines only if the flywheel is 100% PERFECT WITHOUT WEAR. Check nothing fouls when bolting up in case of mismatches. Buy the best as we have tried the rest.

Non injection cars do not need the clutch trigger alignment correct to work but Injection cars do require the correct assembly. Use your original centre boss to ensure correct pick up point positions. The centre boss is available as DAM5921.

Clutch kits should be re-balanced to the flywheel assembly as originally done on production. This is because the verto pressure was a heavier item and the main mass rather than the flywheel as on earlier diaphragm models. This was recognised as a small design fault but easily overcome by balancing which is why Rover originally supplied complete balanced Verto assemblies as repacement parts.

Do not forget to change the AAU2866 seal for the clutch release bearing to plunger. If you are looking for an upgrade clutch see C-AEG485 pressure plate and your choice of plate.



Please note, bolts are no longer included, DAM5920 x6 required.

($85.50) £85.50 exc vat

($102.60) £102.60 inc vat

In stockIn stock

Recommended usage 1 x CK9378 to fit one mini.

Alternative products

3 piece Borg and Beck Injection Clutch with the larger 190mm wide for 1990 on and all injection cars, but it can be used on earlier non injection Verto type engines only if the flywheel is 100% PERFECT WITHOUT WEAR. Check nothing fouls when bolting u...

People also bought products

Non Genuine three piece verto clutch kit, has a 180mm wide clutch plate, pressure plate and release bearing,fits all cars pre 1990 VERTO assemblies until fitment of 1275cc engines. For Borg and Beck see GCK151MS

From 1990 on the...

Verto 20% upgraded performance pressure plate which should be used with 190mm organic clutch plate C-AHT594 or the paddle type drive plate as used in racing C-AHT600. This pressure plate has a blue paint identifying mark and...

Upgraded Centre boss for all verto clutch/flywheel.

Fixing bolts are DAM5920 which are supplied in many clutch kits.

Clutch housing bolt to engine long 5/16" UNF 1.75" long with tuflock patch to secure. Earlier bolts less tuflock are {link]BH605141{/link}

Performance type Verto 190mm wide paddle type drive plate as used for racing.

This will not fit pre Verto backplate/flywheel as it is to wide.

This Verto type clutch arm is 2.75" long from the clevis pin hole.The earlier type pre verto is over 6"(165mm)long. the ball wears on both types and if the clutch is wrongly adjusted the arm (mainly the long type) can bend by way of hydraulic pressur...

For pre injection Verto clutch cars with pre engaged starter, it is also designed to increase clamping

pressure which effectively upgrades the actual performance of the verto clutch, which with the AP pressure GCC679 (part of G...

When the verto clutch was introduced the factory started fitting this plastic protector over the clutch oil seal on Metro's. It then apeared on injection minis with LUF10005 clutch seal to the end of production. Should be replaced when s...

3 piece Borg and Beck Injection Clutch with the larger 190mm wide for 1990 on and all injection cars, but it can be used on earlier non injection Verto type engines only if the flywheel is 100% PERFECT WITHOUT WEAR. Check nothing fouls when bolting u...

If your 1982 on model Mini has a short (3" or so) clutch arm, you have a "Verto" clutch. This is your clutch plate disc if it is 180mm wide. If your car is 1990 or later you have a 190mm wide GCP90832AF plate. Thickness 7.69mm.

If your late model Mini has a short (3" or so) clutch arm, you have a "Verto" clutch. This is your release (throw-out) bearing. Retaining o ring is AAU2866.

MPI flywheel, must use VALEO pressure plate/or C-AEG485 Minispares uprated pressure plate OR THE ENGINES WILL NOT START BECAUSE THE TIMING SLOT WILL BE OUT.

Twin point injection cars had 190mm clutch plates. C-AHT594

Sleeve that covers the flywheel bolt on verto clutches for the release bearing

Note--early 58mm internal diameter sleeves had a plastic anti rattle sleeve which is no longer available but this later type is smaller in diameter and therefore ...

3 piece Borg and Beck kit, has a 180mm wide clutch plate,pressure plate and release bearing,fits all cars pre 1990 VERTO assemblies until fitment of 1275cc engines.

From 1990 on the clutch plate was increased to 190mm, for 1275cc which is ...

AP Technical department recognised that GCC679 with a green paint identifying mark as their best for clamping pressure to date, apart from the 20% uprated version C-AEG485. For performance engines it works best by fitting [l...

This is the only aftermarket copy of the GSY118 available and have been sold by us for many years without any problems. We always recommend genuine but the choice is yours. I would stick to the original from AP lockheed if keeping the ca...

Genuine AP from original tooling. The latest model Minis have a different design clutch and thus a unique slave cylinder. The cylinder mounts more vertical than horizontal and even looks a little strange. The Mini clutch slave cylinder is a vital l...

This is the bracket for supporting the slave cylinder and often fractures around the bolt hole areas as well as across its main body. The spacer between clutch case and this bracket has been made obsolete by Rover but we use 21A1108 whic...