GEAR LEVER RETAINER PIN LONG
DAM2670

($2.33) £2.33 exc vat

($2.80) £2.80 inc vat

In stockIn stock
rod change gearlevers are held in place by retainer 22G1434 and there are 2 locating pins in the alloy housing. the long pin is DAM2670 and the short one is 22G2272

($2.33) £2.33 exc vat

($2.80) £2.80 inc vat

In stockIn stock

Recommended usage 1 x DAM2670 to fit one mini.
Rod Change Gear Shift Mechanism - Qty 1
Gear Lever and Selector Mechanism - Qty 1

People also bought products
PRIMARY GEAR BACKING RING GENUINE
88G549GENUINE

Genuine Rover spacer that fits up against the primary gear on the crankshaft and held on by the "C" washer 22A319 - both these parts wear as well as the gear.

Mini Spares also produce a ring 2 thou thicker 88G549 to...

($13.00) £13.00 exc vat

($15.60) £15.60 inc vat
DIFF HOUSING LOCK TAB ROD CHANGE LH
42H500

Left hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used. For R/H locktab see 22A962

($0.91) £0.91 exc vat

($1.09) £1.09 inc vat
DIFF HOUSING LOCK TAB ROD CHANGE RH
22A692

Right hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used.

($1.35) £1.35 exc vat

($1.62) £1.62 inc vat
GEAR LEVER BUSH FLANGE
22G292

($5.63) £5.63 exc vat

($6.76) £6.76 inc vat
PINION "C" SHIM .004"
GUG705646GM

The shims go against the mainshaft double roller bearing securing cap in your gearbox to give it pre load. See workshop manual for advice but you are aiming for only 1 thou pre load.

($0.79) £0.79 exc vat

($0.95) £0.95 inc vat
SINGLE ROW RHP ROLLER. 4 SYNCHRO
ADU7619

Genuine 1ST Motion shaft SINGLE track original bearing for 4 synchromesh 1st motion shaft.

This is a Genuine RHP bearing, and should not be confused with cheap alternatives. The cheap aftermarket bearings often fail and the work involved to...

($34.97) £34.97 exc vat

($41.96) £41.96 inc vat
BALL BEARING FOR DETENT SPRING
BLS110

When you take the side cover off the differential housing on a rod change type gearbox this detent ball sits behind the spring-the spring is 22G2083 and the sleeve is 22G1870. The oil seal for this is 22G1417.

($0.22) £0.22 exc vat

($0.26) £0.26 inc vat
COMPETITION STEEL BAULK RING
C-22A1741

Mini Spares Performance Baulk ring.

The standard sintered baulk (synchro) rings are not tough enough for the demands of performance useage, in many instances lasting only one race before failure or breakage. The main reason is the incompat...

($35.36) £35.36 exc vat

($42.43) £42.43 inc vat
DIFFERENTIAL ROLLER RHP manufacture
AHU1856

Genuine RHP as originally fitted to every production Mini.

Two of these main diff carrying bearings are required in the gearbox and this new steel caged type fits either way round. Should be pre loaded by 1-2 thou.

Some original fi...

($28.29) £28.29 exc vat

($33.95) £33.95 inc vat
BRONZE THRUST WASHER FOR PLANET WHEEL PRE A+
2A7062

The bronze washer for the planet gears in the differential for pre A plus gearbxes. You can use the DAM5071 and cut the lips off.

($2.22) £2.22 exc vat

($2.66) £2.66 inc vat
GEAR CHANGE BUSH. PRE ROD FOR GEARBOX LINKAGE RODS
2A3502

The bronze bush in the differential housing that the gear change selector rod sits through which should be lightly greased.

($4.20) £4.20 exc vat

($5.04) £5.04 inc vat
OUTPUT SHAFT COLLETT
88G493

Only fitted to vehicles with hardy spicer output shafts (Cooper S and autos). Two collets are fitted in the output shaft in the gearbox and located behind the rubber seal 22A1566

($5.75) £5.75 exc vat

($6.90) £6.90 inc vat
CLUTCH CASE STUD SHORT 3 REQUIRED
53K547

Stud to hold the clutch case to the engine and gearbox, 3 of required. 5/16"UNC thread for alloy fitment for gearbox with UNF thread the other end for the nuts. These are 1.5"long.

The 6 longer ones are 22A152.

These st...

($0.59) £0.59 exc vat

($0.71) £0.71 inc vat
BALL BEARING FOR SYNCHRO HUB 3&4 SYNCHRO
BLS107

Inside your gearbox synchro hubs are 3 springs and these ball bearings to lock it in and out of gear. Often pop out and get lost when splitting the inner and outer hub.

($0.45) £0.45 exc vat

($0.54) £0.54 inc vat
IDLER NEEDLE ROLLER FOR A PLUS GEARBOX
TUK100320

Torrington/Koyo idler gear bearing with special rollers for allowing movement on late type idler gears. The idler gears for twin point cars were also made from clean steel as an upgrade from 1996 on. This special bearing replaces the cheaper inferior...

($8.25) £8.25 exc vat

($9.90) £9.90 inc vat
IDLER GEAR 4 SYNC PRE A+ NEEDLE ROLLER
13H7848

Bearing 26.9mm wide to take 19.05mm idler gear shaft that fits in the gearbox case and clutch housing case on 4 synchro gearboxes until introduction of A plus when a larger bearing was fitted.

($5.25) £5.25 exc vat

($6.30) £6.30 inc vat
LAYSHAFT NEEDLE ROLLER (ALL PRE A+)
88G396

When in doubt replace it. You have heard this many times but you better believe it on this part. If you have not personally just replaced these layshaft bearing then do it now while you have the chance. These bearing will destroy the inside of a very...

($3.27) £3.27 exc vat

($3.92) £3.92 inc vat
DIFF SHIM 6 THOU
DAM3108

You will need to shim up your diff bearings with these washers as required. See workshop manuals for details. See also DAM3109 & DAM3633.

($0.79) £0.79 exc vat

($0.95) £0.95 inc vat
IDLER GEAR SHIM A PLUS SHIM KIT(5 SHIMS)
DAM4821

This kit contains 1 each of 3 alternative sizes plus 2 of the standard size shim

for shimming idler gear on A Plus idler gears. These are the later type spec

which rover superseded to when upgrading the idler gear material on inject...

($78.75) £78.75 exc vat

($94.50) £94.50 inc vat
LEVER ROD LOWER.ROD GEAR CHANGE
22G1847

For the rod change gearbox, this is the lower of the 2 bell lever cranks that sit on a pivot pin on the bottom of the case. The upper one is 22G1848 and the larger protruding one at the very bottom, AHU2292 is for reverse. The fork has 2...

($11.20) £11.20 exc vat

($13.44) £13.44 inc vat