($120.16) £120.16 exc vat
($144.19) £144.19 inc vat
In stock
($120.16) £120.16 exc vat
($144.19) £144.19 inc vat
In stockRecommended usage 1 x GXE7708KIT to fit one mini.
Mk3 round body type wiper motors sat on this black rubber insulation pad
When replacing the 520160A parking switch the inner contact areas on the wiring loom are also worn or damaged so we produced this socket and small length of loom.
Upgraded Mini Spares product in stainles steel. You probably will never break this item, you're more likely to buy it for it's looks. This mounting strap fits all late model cars with the round wiper motor. The strap is polished stainless steel compl...
For classic vehicles with self parking wipers.
We all love our classic vehicles and many of us use them all year round. This means facing the vagaries of the weather, and let’s face it, even summer weather is rarely as rain free as...
Wiper motor fitting kit to fit all mk2 onwards wiper motors to the bulkhead.
Original manufacturer LESS THE GEAR 608092A this same wiper motor has been fitted since the late Mk2 version 1968/9 and is still used on the latest twin points but is wired up to give 2 speed and intermittent wipe.
The gear is ...
Plastic gear with 110 degree wiper sweep for all mk2/3 saloons and vans etc from about 1980 on. This gear has 46 teeth and some pre 1980 vans/pickups had 120 degree(stamped on gear) with same amount of teeth, but was replaced by this. MK1 originally ...
Windscreen wiper wheel box fitted on Mk3 Minis from 1971 on plus all Mini Clubman. 32 teeth.Sold singly 2 required per car
The wiper motor drives a rack inside the metal tube that fits beneath the dash of the Mini. The rack is very well protected inside the case, but the problem is that the tube is often bent and/or rusted. Our special kit supplies all 3 pieces and the...
Original manufacturer LESS THE GEAR 608092A this same wiper motor has been fitted since the late Mk2 version 1968/9 and is still used on the latest twin points but is wired up to give 2 speed and intermittent wipe.
The gear is ...
This is the spiral wound cable that is in the wiper rack tubes. It needs to be cut to length.
Total length uncut is 150cm.
Fits the end of the wiper motor to hold the outer casing to protect the rack cable which drives the wheel boxes. Not supplied with new motors.
Wiper motor fitting kit to fit all mk2 onwards wiper motors to the bulkhead.
Main wiring grommet that fits in the front parcel shelf. ID 12.5mm fits 35mm hole.
This is the wiring required if you have side repeater lamps on your front wings including bulb holder, grommet and connectors LESS the bulb. The large grommet that sits in the inner wing where the wires go through is YML10654. sold indiv...
Reverse lamp as used on some Mokes/kit cars etc, essentially the same as our indicator lamp CHM13WHITE but with a clear single filament bulb rather than orange and white plastic lens.
rear stop and tail lamp for early BMc cars with red plastic lens.
Also stocked is a white lens and single filament bulb equivalent for use as reverse light on kits cars and Mokes as CHM13REVERSE.
Wiper Swithch MK1/2/EARLY MK3 blade type switch for using to convert to 2 speed wipers when current 2 speed wiper motor is used.
NEGATIVE EARTH ONLY..45D electronic(contactless)Pre A plus distributor .
replaces 41824A and 41418 plus any 998/1098cc up to the changeover of A plus type distributors. For best performance and tune we advise our electronic evolution versio...
Stainless steel coil bracket for 1970-1996 cars.
Coil bracket fitted to end stud of cylinder head,clutch end for coil to mount on as fitted 1969-94-MK3 on. This has been made to the original specification with the welded lug nuts rather than the cheaper method of having just plain holes to take a b...
Screw for holding PRC1230A to the number plate light body, 1970 onwards.
Screw for chrome metal number plate lamp on mk3 19790 on - You will have to drill the lens out to take M4 screw.
Best on the market, sports coil-Not Lucas. A standard coil can only do so much, and when compression is raised (as in most high performance engines) or improper fuel mixtures occur something better is needed. This sports gold coil with proven origina...
Repair loom and plug for all post 1976 headlamp switches.See PM08 for headlamp switch with plug and correct wires colours for loom repair
Replacement distributor cap retaining clip for all 45D type distributors-sold per clip.
THE LENS FIXING SCREWS FOR THE REAR LENS ON MK4 1976 ON WITH REVERSE LENS ARE ALL THE SAME. SOLD INDIVIDUALLY. ALSO FITS TWIN POINT FRONT INDICATOR LAMP.
3 per lamp required or 6 per car set.
With an integral push start button built in the solenoid as originally fitted to early minis. The activation of the starter motor starts with the key (or push button in the early cars), but the most important function is carried out by the solenoid....
THE ELECTRICAL CIRCUIT FOR THE FUEL PUMP INCORPERATES AN INERTIA FUEL SHUT OFF(ifs) SWITH WHICH WILL STOP FUEL BEING DELIVERED TO THE ENGINE IN THE EVENT OF SUDDEN DECELERATION--It is fitted in the engine compartment, fixed to the bonnet switch brack...
Lucas upper lens plus gaskets for cars with built in reverse facilty in lamp
These are the upper lens in clear plastic with 2 new lens gaskets to stop water seeping into the lamps, plus the correct bulbs when you require the fashionable clea...
Sold individually, these are R/H/D.
RHD HEADLAMPS DIP TO THE LEFT.
Brand new Free Form light unit from Wipac with clear Polycarbonate lens but the backing bowl is specially designed to reflect the beam and give better pen...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.