($98.06) £98.06 exc vat
($117.67) £117.67 inc vat
In stock
parts in kit to transform handling are
21A1091 comp tie bars
C-AJJ3320 adjustable lower arms
C-STR627 performance tie bar bushes
C-STR632 performance lower arm bushes
Fixings for the above
($98.06) £98.06 exc vat
($117.67) £117.67 inc vat
In stockRecommended usage 1 x MSSK3008 to fit one mini.
SAVE 25%-Geometry kit, same as MSSK3013 but without the correct special rubber bush kits.This kit saves over 25% on cost of individual parts.
This kit is for customers who wish to fit their own choice of bushes but
Mini...
Ultimate road or race geometry kit which includes following parts. Adjustable tie rods and lower arms with the correct bush kits. For the rear a set of camber and tracking brackets. When fitted the suspension must be properly set up. This kit will dr...
Original Bolt with a special length shank for the front suspension tie bar to the lower arm. Always check this out for any signs of wear and replace accordingly.
Only wrong length parts were available in the market so these are the correct l...
This is the correct thick flat washer for a suspension tie bar rod. The washer has a 7/16" hole is 1.5" wide. See 2A4328 for the correct dished washer.
Ultimate lower arm for road or race. (pair supplied)
One piece, forged, fully adjustable on the car lower arms (with knuckle for bushes) to allow adjustment for any camber setting required. Sold in pairs only. It is recommended that you fit ...
Pair of adjustable tie rods. See 21A1092 tie bar kit.
When you change the length of the lower control arm to attain the desired degree of camber, the caster also changes. To reset it you must be able to change the length of the ...
Large cup retaining washer for the front suspension tie rod.
Sold singly 1 required per rod and 2 per car
Mini Spares product UK made especially for use when geometry has been changed, such as fitting adjustable tie rods or lower arms, or on any cars with corrected castor angles.
Set of 4 bushes.
These metal sleeved bushes are specially...
Uses 2 Soft standard rubbers on the insides and the 2 Mauve poly on the outside.
HARD OUTERS / SOFT INNERS - STOPS BRAKE WEAVING.
Don't be confused as this special shore hardness set up was proven after 2 years of testing and is per...
Ultimate road or race geometry kit which includes following parts. Adjustable tie rods and lower arms with the correct bush kits. For the rear a set of camber and tracking brackets. When fitted the suspension must be properly set up. This kit will dr...
The amount a wheel leans in or out at the top is called "camber". As the car turns and the body leans the tire can lose traction as it no longer is making full contact with the road. When the top of the wheel leans in toward the center of the car it'...
SAVE 25%-Geometry kit, same as MSSK3013 but without the correct special rubber bush kits.This kit saves over 25% on cost of individual parts.
This kit is for customers who wish to fit their own choice of bushes but
Mini...
The amount a wheel leans in or out at the top is called "camber". As the car turns and the body leans the tire can lose traction as it no longer is making full contact with the road. When the top of the wheel leans in toward the center of the car it'...
Set of 4 High quality Japanese sealed ball joints.
Developed and tested over a period of three years, the original concept was to manufacture a high quality product, similar to those used on modern vehicles. Unlike the current des...
Genuine Mini Spares standard performance cone utilizing 20 years of elastomer/rubber technology from our competition cones manufacturer. Only beeen available since 02/09/2020 and proudly made in the UK with 10,000 sold by 2023.
Original cone...
Lightweight drilled version of 21A2596. This bolt is drilled all the way through to allow easy adjustment of Hilos.
Genuine Mini Spares UK made complete joint with the following specifications,
correct dimensions and shape of pin and ball in EN24T, using correct spec grease,
genuine original shape cup using correct material (21A423MS...
Rebound buffer that fits under the top arm now in polyflex, mounted on a stainless steel mounting base
Polyurethane upgraded gaiter for all knuckle joints and many track rod ends
For standard rubber versions see 21A425
please note- this does not fit all track rod ends as so many genuine and aftermarket parts have been s...
Captive nut plate that sits behind the damper bracket on the inner wing/bulkhead to attach the damper brackets. 2 PER SIDE.
All the Nuts, bolts and washers you will need to fit a rear subframe to your car, less the support pins and bushes. These kits are aimed at those wanting to fit different rear subframe bushes such as the Poly bushes.
All the Nuts, bolts and washers you will need to fit a rear subframe to your car, less the support pins and bushes. These kits are aimed at those wanting to fit different rear subframe bushes such as the Poly bushes.
Mini Spares product,metal trunnion to hold the 2-2A5818MS bushes on the rear subframe.
Originally there were 4 of these trunnions on the subframe but in 1976 (MK4)the front 2 brackets were strenghened and enlarged to [link]21A2...
Mini spares product.In 1976 Rover started fitting this larger metal trunnion to the front of the rear subframe which only used one single large bush 21A2560.
2 required per car but sold singly
New Evolution design in 4mm thick metal mase to fit Genuine and our non genuine subframes better than the standard originals.
The amount a wheel leans in or out at the top is called "camber". As the car turns and the body leans the tire can ...
Fast Road Gmax gas filled rear shock absorber (sold individually). Only for lowered cars.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.