($13.62) £13.62 exc vat
($16.34) £16.34 inc vat
In stock
($13.62) £13.62 exc vat
($16.34) £16.34 inc vat
In stockRecommended usage 1 x SEN44 to fit one mini.
Special formulated hose for brake servos and engine emmission breathers sold in a 22 inch length. 3/8" inner bore.
From 1989 minis which have the brake servo built into the master cylinder and it is very difficult to work in the engine bay, especialy clutch changes because of the extra room taken up by this dual cylinder. By replacing the 2 metal brake pipes from...
A pair of black painted servo brackets for MK1 cars or when using the 21A1293 servo.
Genuine AP product-HOSE FITTING EITHER END in-line brake servo valve which is essential if you do not have the correct U shape section formed in the servo hose to stop petrol contaminating your servo. Not supplied in any kit it is an important part. ...
Mini Spares copy of original AP Lockheed Mk1/Mk2 "S"servo which have not been available for decades. Using the correct cast iron body it is dimensionally the same as the 5.5 Lockheed type 112756 as fitted to the original Cooper S Mk1/2.
(Thi...
The latest model of the servo used on the Mini and some other cars is a very dependable unit. But it still has rubber parts inside and these do wear out. Several things will tell you when it's too late to do preventative maintenance. If you are slow...
For Cooper S 7.5" wide discs these are our favourite road brake pads as the reduce contamination on alloy wheels by virtue of less brake pad dust, plus they work well with good anti fade properties.
The rubber type grip fitted on handbrakes-
will fit any single cable hand brake from 1976 on
Mk1/2 used 13H5541 thinner plastic type--to fit this to pre 1976 early cars you will need to put lots of sticky tape on the h...
Adjustable original brake proportioning/balancing valve for racers only.
The most common brake system on the Mini has Disc brakes in the front and drums in the rear. The weight bias on the car is all in the front and thus under hard braking...
Original AP Lockheed type metal body master cylinder.
Fitted with a plastic cap the metal original alternative is available seperately as 17H5323
Ensure the correct DOT4 or DOT5.1 brake fluid is used as these cylinders...
These repair kits are for the later twin leading front drum brakes wheel cylinders GWC126/7 with .9375" bore size. The earlier twin cylinder set up used part number 8G8816 for GWC102/3 with 0.8125" bore size.
Correct size and length brake pad pin for the caliper using 7.5" disc size as fitted to Cooper S and 1275GT. 4 required for 1 car, also fits Cooper 7" calipers. 3mm diameter.
Brake and clutch pedal pads contribute to comfort and safety. They also add that final touch to a nice interior. GPR104 fits brake and clutch pedals of MkI & MkII Minis up to 1976 and the throttle pedal on post 1976-1996 models.
Set of 5 braided hoses. 2 front brakes, 2 rear brakes, and clutch hose for pre A+.
If it is time to replace the brake lines on your Mini, and it probably is, you should consider replacing them with braided-steel hoses. They are direct bolt...
The screw that holds the drum on the hub. Earlier hubs had two screws, many replacements have only one, all that’s needed.
Brake light switch for pre 1976 minis with single line brake systems. Fits into banjo bolt (7H7995) located at O/S front brake hose. This switch has a tapered thread. Made by a UK company who suplied parts to Unipart.
For minis ...
Brass 2 way brake union that bolts on front subframe.
Genuine AP Lockheed boxed and made in UK. FRONT TO REAR master is the latest model dual master cylinders, which was introduced in 1985 with a stepped bore of 17.8 to 19mm to replace any previous master cylinders from September 1978 to 1988 when the b...
Rubber gaiter to keep debris from entering the drum via the backplate handbrake lever SMN10005. Sold singly per backplate, 2 required per car.
All MK1/ MK2 Minis including all Cooper and "S" versions plus MK3"S" only.
This valve was fitted to every MK1/2 car including Cooper and "S" and the MK3 Cooper "S" only.
All other MK3 versions 850/998/1100 use 21A2031 w...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.