(7,10 €) £7.10 exc vat
(8,52 €) £8.52 inc vat
In stock
(7,10 €) £7.10 exc vat
(8,52 €) £8.52 inc vat
In stockRecommended usage 2 x 21A1520 to fit one mini.
Replacement ball joint shims, comprising of 2x 003"(.076MM) shims, 2x 005"(.127MM) and 2 x 010"(.254MM).
Tie rod extra hard rubber bush, harder than standard.
You dont want these bushes too hard as it can cause the threaded on the end of the tie rod to break under extreme conditions.
In theory the outer ones should be harder for rigidi...
extra parts required to convert the C-AJJ3360 lower arms to spherical rod end type if the arms were previuosly purchased-These parts are available with the arms as C-AJJ3360A as a money saver
Angled grease nipple for the upper arm on the front suspension of all Minis
importantly lubricates the upper arm spindle which so often gets neglected so check yours out and make sure this nipple is working properly. Also fits rear radius ar...
The term 'hydro' in the renowned Cooper "S" suspension system "Hydro-lastic" means at least in part a liquid. This famous system was designed by BMC make for smooth and fluid ride while taking all of the abuse of off road rallying. It is not uncommon...
Mini Spares own to original drawing specifications with heat treatment correctly applied where appropiate.Lack of proper maintenance (grease) will make the pivot shaft and/or bearings wear that much faster. In severe cases the shaft may rust to the b...
Special shims for adjusting your swivel pins on the front hub. See workshop manual for correct settings - these are 005 thou but if you need 10 thou see 2A4241.
The front tie rod on the Mini controls the fore and aft location of the lower front suspension arm of the car. In addition it provides a great degree of stability under braking. If your rod is bent or the bushes are worn then you need help. The Tie r...
Floor pan front to rear for the left hand side, only to the floor shape before rod change cars - ideal for MK1/2 restoration.
The weathered and cracked rubber you see is not actually the hydro displacer bag, but rather this rubber boot to protect it. Sold singly 1 required per displacer.
For Hydrolastic suspension cars, they were made with a 1/4" fixing hole but this needs elongating vertically to get the bump stop to sit properly on the upper arm which had different machine tolerances when manufactured.
Have you got one of the rare "wet" suspension Minis? This is the retainer plate that holds the protective sleeve around the hydro hose on the bulk head panel.
Sold singly 2 required per car.
Sold in pairs only.
These arms will give an extra 1.5 degrees extra negative camber over what the standard arms give on your car. To correct all variations of incorrect geometry found on the mini we have produced a pair of on car adjustable ...
Longer track rod end for running with negative camber, gives an extra 5mm of adjustment approximately over the standard item. Has consistent thread pattern and perfect design to our requirements to fits all known racks and classed as a competition tr...
Front hub nut that screws onto the CV joint of all early minis with drum brakes plus all standard cooper 997/8 models. 1 1/8, 1.125" AF nut size although 28mm width have been seen. The washer for this is 2A7323.
Fits top and bottom of the front damper and the lower rear damper to keep the bush from moving in the damper (shock absorber) eye sockets. 3/8"hole.
1.4mm thick by 24.6mm wide.
Same bump stop as fitted to MGB, this was utilised by ST Works Abingdon to go on their bump stop kits C-AJJ3313/4007 for hydrolastic minis. Sold singly.
Original genuine standard tie bar bush (2 per rod) but sold individually.
These bushes are made to the original drawing and specifications by the original manufacturing company for BMC/Leyland & Rover.
These genuine bushes are soft ...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.