(82,22 €) £82.22 exc vat
(98,66 €) £98.66 inc vat
In stock
(82,22 €) £82.22 exc vat
(98,66 €) £98.66 inc vat
In stockRecommended usage 1 x 24A1256 to fit one mini.
MK1 fresh air hose clip on righthand inner wing, can be used on mk4 onwards lefthand fresh air vent hose.
Fitting kit comprising of studs, nuts, plain washers, spring washers and a gasket
Heater vent demister covers for the pre 1969 heater assembly.
Genuine Mini Spares heater valve. The original RANCO tooling has been scrappped so beware of some imports available where the inners quickly explode loosing the metal cap and all your water when operated.This has M4 metric thread bolt included for th...
Fitted from approx 1969 to 1988 they replaced the original knob with the word PUSH and HEATER. This was done as a safety feature by having a rubber edge. The grommet in the body for this cable to pass through is CAM5969. Cable length is ...
from air vent on dash to duct-about 5"(128.9mm)long with 2.5" diameter
The heater is not available any more, but this matrix is the main component which gets blocked up or leaks, stopping it blowing hot air. This is a new heater matrix for late MK1 plus MK2 cars has 4.5" gap between pipes with opposite outlets for cars ...
This gasket fits on the cylinder head for every A series heater valve or outlet pipe until the hole was no longer drilled when they changed to a heater valve fitted into the hose line from 1990 on.
The heart of your heater is the radiator matrix which often gets overlooked when cleaning the cooling system. They often get clogged and cannot be cleaned rendering your heater useless. Replacement is the only answer if flushing out does not clean it...
Heater valve studs fitted to the cylinder head. 1/4"unf 1.1250" long.
Twin point Mini heater tap that fits to the heater assembly
Without doubt the best hose to fit unles you are after the lovely silicon
extra strong and supple hoses. See GRH1006 for lengths required if you are not sure on your car.
From 1989 until the introduction of the twin point injection cars, Rover fitted this in line floating heater valve which was the first time they never bolted the heater valve as a direct outlet on the cylinder head. A strange looking black plastic va...
This is the specially made grommet which fits into the body to allow the 1/2" heater hose to go through the body on the right hand side of the bulk head panel, as fitted originally on Mk3 shells to 1989 with round holes in the body as opposed to elon...
3 YEAR GUARANTEE-UK made.Large impeller higher capacity water pump with top quality die cast body . Mini Spares procured product as the original superb Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impeller...
3 YEAR GUARANTEE-UK made. Large impeller higher capacity water pump with a high quality die cast body. A Mini Spares procured product as the original superb Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impe...
Unless your're heavily into the concours scene you'll love these hoses! These silcone hoses will withstand higher temps and pressures and will last virtually forever! Made to fit 1275cc cylinder head the length is made to cover 1275cc engines includi...
Black Silicon Bottom hose- Unless you're heavily into the concours scene you'll love these hoses! These silicone hoses will withstand higher temps and pressures and will last virtually forever! And if you ever had to replace a lower hose you'll appre...
Complete fixing kit for a water pump, includes replacement silicone bypass hose, clips, superseal gasket, replacement bolts and washers.
This thermostat housing fitting kit, suitable for all single tier thermostat housings. Comes with new studs, nuts, washers and Klinger thermostat housing gasket
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.