(0,98 €) £0.98 exc vat
(1,18 €) £1.18 inc vat
(0,98 €) £0.98 exc vat
(1,18 €) £1.18 inc vat
Recommended usage 1 x 2K8686 to fit one mini.
These copper sealing washers should be replaced every time the hoses are undone as a precaution. 10mm i/d, 15mm o/d. is smaller than a 3H550
1.4mm thick copper washer for all clutch and brake joint uses. This washer is 17.4mm wide with an 11.4mm diameter hole. Larger than a 233220A.
This special shake proof washer should be replaced. Found on front hose.
Also used on 21A1524 hydrolastic pipe adaptor.
Genuine AP set of 4 rubber brake hoses (front hoses are longer than in other kits for drum brakes).
Genuine AP car set of 4 brake hose for cars with front disc brakes. If you are changing one through wear and tear it is a good idea to change the whole set and save money with peace of mind about your brake system. Securing nuts included
Clamp plate to hold servo brake pipes. Two required. Fitted to Cooper S and early 1275 GT. 1963 TO 1974.
Non spacered die cast alloy brake drums. The alloy material has a finned design that dissipates heat quicker which in turn helps reduce brake fade. Sold as a pair of drums.
Set of 4 hoses, 2 front and 2 rear.
Braided brake and clutch hoses have a PTFE inner which helps to eliminate the spongy pedal feel under arduous conditions, and give greater efficiency. The outer braided stainless steel cover e...
Set of 6 hoses, 4 front and 2 rear to fit the ERA turbo.
Braided brake and clutch hoses have a PTFE inner which helps to eliminate the spongy pedal feel under arduous conditions, and give greater efficiency. The outer braided st...
NICKEL copper easy bend brake pipe with 2 metric male unions. 22"long, for 1988 on master cylinder lower outlet to PDWA valve outlet nearest to wing-other pipe is HMK026-both for left or right hand drive.
These pipes are retail...
We now supply 2 easy bend copper nickel pipes with the correct unions for when converting to the later type GMC227 front to rear split master cylinder.
4 pins supplied (clips are no longer available)
Correct size and length brake pad pin for the caliper using 8.4" disc size and vented calipers.
Brake pipe with male metric ends, 12mm for master cylinder and 10mm for PDWA valve. fits in the bottom union and goes to left hand union in valve (to go to rear brakes)
Road use pads but for performance use C-AHT223GREEN these are original size 2.375" which fit later 997 cooper- but if you have the very early small pad type, 2.125" wide for 997cc less split pin holes, these are nearly obsolete you can g...
Brake pipe with male metric ends, 12mm for master cylinder and 10mm for PDWA valve
As the original brake pipe kit is now obsolete, we now supply 2 easy bend copper nickel pipes with the correct unions for when converting to the later type GMC227 front to rear split master cylinder.
For use on 8.4" wide standard brake disc calipers, 2.920"wide.
This is the Ultimax upgrade which produces less brake dust which destroys alloy wheels. For the upgraded version of this see C-AHT16GREEN.
A set of split pins are availa...
A great street upgrade for 4 pot calipers giving off less brake dust and better efficiency.A set of split pins and metal retaining clips are available as GBK1025
Our favourite pads as the give less brake pad dust which destroys alloy wheels.
Very durable and great for most road usage. The green upgrade for fast street is C-8G8995GREEN.
Less Brake Dust and better stopping power!! The best pad available seems to be the only pad set available now as Rover/Unipart etc have all deleted it from their range
For Cooper S 7.5" wide discs these are our favourite road brake pads as the reduce contamination on alloy wheels by virtue of less brake pad dust, plus they work well with good anti fade properties.
For use with 4 pot calipers as per Metro or Minispares own alloy type these are our favourite road brake pads as the reduce contamination on alloy wheels by virtue of less brake pad dust, plus they work well with good anti fade properties. A set of s...