(199,00 €) £199.00 exc vat
(238,80 €) £238.80 inc vat
now
(169,15 €) £169.15 exc vat
(202,98 €) £202.98 inc vat
In stock
(199,00 €) £199.00 exc vat
(238,80 €) £238.80 inc vat
now
(169,15 €) £169.15 exc vat
(202,98 €) £202.98 inc vat
In stockRecommended usage 1 x ASJ36002 to fit one mini.
This late front (nose) panel will fit any Mini, with rubber mounted subframes, manufactured after 1976. It is probably easier to replace the entire panel than to repair a damaged one, especially if it's been hit more than once! Early Minis can use [l...
This late front panel will fit any Mini, with rubber mounted subframes, manufactured after 1976. It is probably easier to replace the entire panel than to repair a damaged one, especially if it's been hit more than once. Early Minis can use [link]MS4...
This Non genuine pattern panel has the holes for windscreen wipers and jets with barely an inch of pillar.
On cars from 1992/3 on check the original windscreen drain channel as the VIN numbers were stamped above the clutch master cylinder-wi...
Reproduction version os ASJ360070. For the twin point only as it changed shape to accommodate the front mounted radiator and different bonnet fittings.
For vehicles with external hinges and sliding type windows this is a full inner front wing with the wheel arch panel. The panel is what that the outer A panels for the hinges attach to. This is the right hand panel made by Heritage but not 100% perfe...
Aftermarket version of the L/H floorpan for 1991 on cars.
This floor was made stronger with smaller heel pad area to prevent vibration and rust and will fit any Rod change gear shift mini but was introduced on the first injection cars in 199...
A non genuine panel made for repairing the corner of the windscreen panel which is prone to rust from water splashing up from underneath the front wheel arch.
Experience has shown its easier to fit the genuine panel HMP441001 al...
You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width with vertical flanges for easy installation and fairly well represent the original stamping. They have added metal to include...
Inner front L/H wing with the A panel and door stiffener check strap panel attached for ease of fitment and alignment.This has the large round hole for the fan as fitted from 1991on
You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width with vertical flanges for easy installation, and fairly well represent the original stamping. They have added metal to includ...
If your rusted old headlight bucket is getting to you, don't waste time trying to salvage it when new metal reproduction metal buckets are AVAILABLE.
With a headlamp rim fixing bracket 37H7421 attached
Whether you are ...
THIS PANEL PROTECTS THE UNDERSIDE OF THE WINDSCREEN VALANCE UNDER THE FRONT WING SECTION also fitted on the inner wing panel 14A8346/7
This panel has mounting holes for later models facia crash panel. These holes will require blanking for true originality on earlier models without the facia pad
Inner l/h wing with large fan hole from 1991-96. This panel is available with the A panel fitted for ease of fitment as ABD36005
Was ABD36009 but that did not have the stiffener plate for the damper bracket fitted which was diff...
Inner front R/H wing with the A panel and door stiffener check strap panel attached for ease of fitment and alignment. Always check the bonnet prop bracket location as they changed.
See ALA5661MS for an upgraded thicker and best fitting aftermarket L/H A panel-all the local bodyshops fit this.
Known as an A panel this is for all wind up widow type cars with internal door hinges and is single skin as opposse...
This late front panel will fit any Mini, with rubber mounted subframes, manufactured after 1976. It is probably easier to replace the entire panel than to repair a damaged one, especially if it's been hit more than once. Early Minis can use [link]MS4...
Aftermarket version of the R/H floorpan for 1992 on cars.
This floor was made stronger to prevent vibration and rust and will fit any Rod change gear shift mini started on the first injection cars
Right hand inner wing section only for MK3 cars with 3 air vent holes. One with 4 bolt holes,one with 4 castellated bolt holes (nuts welded in place) and one large trunk hose hole at front. If you want the same panel with A panel combined for better ...
This late front (nose) panel will fit any Mini, with rubber mounted subframes, manufactured after 1976. It is probably easier to replace the entire panel than to repair a damaged one, especially if it's been hit more than once! Early Minis can use [l...
A non genuine panel made for repairing the corner of the windscreen panel which is prone to rust from water splashing up from underneath the front wheel arch.
Experience has shown its easier to fit the genuine panel HMP441001 al...
Genuine panel that has the holes for wipers and jets with only a few inches of pillar which is basically the area that rots. Also referred to as the windscreen scuttle lower panel. Fitting the genuine type ensures you should get a better windscreen a...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.