(337,50 €) £337.50 exc vat
(405,00 €) £405.00 inc vat
In stock
(337,50 €) £337.50 exc vat
(405,00 €) £405.00 inc vat
In stockRecommended usage 1 x C-27H7774 to fit one mini.
the oil seal to fit on 12A1136 distributor housing. Pre A Plus
the earlier housing 2A612 did not have a seal.
Lots of things have been written about performance plug ignition wires but regardless of what you believe we all know that good wires are a must. This special competiton wires set from the Lucas factory has 8mm wire and the highest performance, no br...
Best on the market, sports coil-Not Lucas. A standard coil can only do so much, and when compression is raised (as in most high performance engines) or improper fuel mixtures occur something better is needed. This sports gold coil with proven origina...
A higher compression engine should have a colder spark plug. The engineers explain that it has to do with flame temperature and overheating the plug. I know from experience that my race engine will melt a street plug. Choose from the following NGK pl...
A higher compression engine should have a colder spark plug. The engineers explain that it has to do with flame temperature and overheating the plug. I know from experience that my race engine will melt a street plug. Choose from the following NGK pl...
ULTIMATE PLUG FOR SINGLE POINT INJECTION OR ROAD TUNED ENGINES. THESE PLUGS HAVE A GOLD PALLADIUM NOSE FOR GOOD IGNITABILITY ON LOW VOLTAGE AND OFFER PROTECTION
ON ENGINE MANAGEMENT SYSTEMS AND RADIOS. BPR7EIX is now supplied by NGK instead...
Resistor for AFU3389LED and AFU3389WLED, this is needed to enable the lamps to function properly. Sold in pairs.
Fits from 103113 chassis number and has 1 plug to the ecu.
The floor starter button switch on the early Mini really adds a mark of distinction; it is a classic item that properly dates the vintage of the car. BUT if it becomes intermittent it’s a real pain…you don't even have a battery cable in the engine co...
The best chrome type available with screw and washer.
A headlight trim ring is only the starting point of a good looking car, but you have to start somewhere. Sold singly 2 required per car. These are the original type chrome over solid bras...
Correct 42watt 12 volt Indicator flasher unit for all MK1 minis easily identified by the locating tag on its end it was the longest/largest flasher ever fitted to the mini.
please note. this unit only works with NEGATIVE ...
6 sided chrome nut for MK1/2 wiper wheel boxes-This had a bycycle thread whereas the later MK3 had a metric thread and was 8 sided.
Also fitted Sprite MK1/2/3 Midget mk1/2 TR4/4A and TR5
Mk1 Mini Indicator stalk green lens. Also fitted to other BMC variants such as Morris Minor. See GLB280 for the replacement bulb
Many intermittent electrical gremlins can be traced to a damaged or corroded bulb holder. This dual element socket is for combined park lamp and turn signal. The rubber boot that is supposed to protect it from corrosion is sold separately as [link]50...
Brake light switch for pre 1976 minis with single line brake systems. Fits into banjo bolt (7H7995) located at O/S front brake hose. This switch has a tapered thread. Made by a UK company who suplied parts to Unipart.
For minis ...
RH lamp assembly MK1,this is the only quality part made in UK from original tooling unlike others available from our competitors.
The MKI Mini is the most sought after and the tail lamps are one of the most distinguishing features.
Mk1 tail lamps each have a pair of heavy rubber foam gaskets. One between the lens and the chrome base, a similar one between the base and the body. Since they are exposed to the sun and easily visible, faded or rotted gaskets can ruin the look of...
The headlamp bucket is isolated from the body with these rubber seals/gaskets.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.