(1,16 €) £1.16 exc vat
(1,39 €) £1.39 inc vat
In stock
such as evolution and Salisbury.
(1,16 €) £1.16 exc vat
(1,39 €) £1.39 inc vat
In stockRecommended usage 2 x CCN122 to fit one mini.
There are 4 of these to each output flange to which the Hardy Spicer joint bolts. The special philidas nuts for these are our number GFK3431.
Sold Individually.
Special height locking type nut for the hardy spicer joints on Cooper S and automatics to fit the 22A1139 bolt. Sorry about the price but only available from Philidas Ltd.
Hardened flat washer to be used with flange type LSD Hardy Spicer C-BTA1262 outputs.
IKO idler gear bearing with special rollers for allowing movement on late type idler gears. The idler gears for twin point cars were also made from clean steel as an upgrade from 1996 on. This special bearing replaces the cheaper inferior earlier bea...
Left hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used. For R/H locktab see 22A962
Right hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used.
FITTED from 1984 on-single locktab for the 3 bolt main bearing(double roller)
housing and deleted 1996 on.locking glue used such as locktite
Minispares were the first company to produce these layshafts for performance engine/gearboxes as the standard type would flex and resullt in the breakage of the bearings causing seizure. Produced in an upgraded material and heat treated to the correc...
Single roller bearing that only fits 3 synchro gearboxes to hold the 1st motion shaft-sporadic stocks only of these bearings as they went obsolete in 2008. These are genuine RHP/NSK bearings
3 of these bolt are used on the speedo housing gearbox front cover-they used to be 53K1474 studs 3.75" long but change to this bolt in 1985 3.25"long 5/16"unc
with tuflock patch to secure.
Used on all mainshafts with 14mm shaft end for the 1st motion shaft---when they went to the 18mm shaft on A plus gearboxes they used DAM7485 which is metric thread.
THIS BEARING HAS PRE A+ INNER DIAMETER AND A+ OUTER DIAMETER. If you have the large A plus idler gear bearing hole and want to use it for the earlier pre A plus small hole type idler gear then this bearing is what you require to sleeve it down in siz...
The shims go against the mainshaft double roller bearing securing cap in your gearbox to give it pre load. See workshop manual for advice but you are aiming for only 1 thou pre load.
Genuine 1ST Motion shaft SINGLE track original bearing for 4 synchromesh 1st motion shaft.
This is a Genuine RHP bearing, and should not be confused with cheap alternatives. The cheap aftermarket bearings often fail and the work involved to...
STRAIGHT CUT 1ST GEAR FOR 4 SYNC SPECIAL TUNING GEARSET. (54,35 €) £54.35 exc vat (65,22 €) £65.22 inc vat
See table of "Straight Cut Gear Kits" and their components
Full rebuild kit less diferential parts.
Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.
This is a full kit of bearings except...
Straight cut laygear for SC/CR 3-sync gearbox.teeth count 13-17-20-23
This little roller bearing goes inside the end of the 1st motion shaft on minis with 14mm mainshaft which it sits on.
This bearing was previously part number 88G409 and a true Rover replacement, but if you have earlier A type gears with the...
