(285,00 €) £285.00 exc vat
(342,00 €) £342.00 inc vat
(285,00 €) £285.00 exc vat
(342,00 €) £342.00 inc vat
The full inner wing with wheel arch section for the mini clubman range --if you need only the first 20" approx of the inner wing see CZH3063.
Complete set of bolts to mount the front subframe on all post 76 single bolt subframes less the large tower bolts and towing eye, enough fixings are supplied for those who wish not to use a towing eye.
Angled spacer washer for Mk1/2 external door hinge cars for the upper hinge
Van L/H full length half floor. You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width and length-plain pressed floor with indents but no carpet brackets or lugs underneath
This is the Clevis pin for the hook part with a spring and spacer only. This fits all Minis and Clubmans as the bracket it attaches to is on all bonnets unless broken. The spring loaded catch is designed to keep the bonnet from blowing open while dri...
Original shape washer jet for Mk1/2 minis. Made to the same specification as the last type made for rover parts sales with a nut on a loose thread so it can be tightened easily by hand in the engine bay without any modifications. Should be used with ...
full inner Right hand wing with wheel arch panel plus the A panel fitted for ease of fitment and alignment for the Mini Clubman with radiator air slats-see also CZH3062 and CZH414
Not usually a stock item but available to order
Original MK1/2 shape with correct 1.25" small neck.
Originally made by Winguard these plastic washer bottles for early Minis were often asked for but rarely available.
The original part number for the Winguard MK1 bottle was ADA383...
R/H Pick Up Non Genuine body section from back of the cab to rear but less rear the rear quarter that holds the rear lamps.Genuine panels are no longer manufactured but this NON genuine part is the only repair panel available which we have also used...
R/H Pick Up Non Genuine body section from back of the cab to rear but less rear the rear quarter that holds the rear lamps.Genuine panels are no longer manufactured but this NON genuine part is the only repair panel available which we have also used...
Lower parcel shelf facia panel with hole for switch panel that sits between the A posts. This is made to fit Mk3 cars from 1970 onwards with soft trim moulding.
see also 14A7175 for the retainer that welds to the top
This Non genuine pattern panel has the holes for windscreen wipers and jets with barely an inch of pillar.
On cars from 1992/3 on check the original windscreen drain channel as the VIN numbers were stamped above the clutch master cylinder-wi...
Really a built up half front end for the mini clubman, consists of a lower panel with headlamp panels,slam panel and stiffener between the front and slam panel. 76 ON--no inner or outer wings
Front and rear screen with chrome plastic insert.Saving nearly 15% on cost of individual partts
Commercial Mini floor extension
It is an essential part for the correct restoration of all the longer wheelbase mini derivatives. From the original tooling.
The left side inner fender of the Mini Clubman should have a metal cowling to focus the air from the radiator to the wheel well. The almost sqaure cowling is spot welded to the inner fender. If you are resoting your car properly you will need to ha...
Full length inner wing for the R/H on mini clubman.
4 Non Genuine door hinges as a car set for wind up window type doors from 1970 on. These are a top quality item as opposed to the cheaper junk version available on the market.
Sold seperately as
top right CZH202MS 1 r...
Available again from genuine tooling
Fits all mini clubmans only. There is no aftermarket version available of this bonnet anymore.
this bonnet MUST use the later 1981 onwards BMP348 / BMP349 hinges
Multi purpose square plastic plug/nut for No8 screw size was used on many door fixings and fuse box to body.
Also suitable for Twin Point indicator fixings.