(5,75 €) £5.75 exc vat
(6,90 €) £6.90 inc vat
In stock
(5,75 €) £5.75 exc vat
(6,90 €) £6.90 inc vat
In stockRecommended usage 2 x GRK2013 to fit one mini.
Genuine AP as supplied to UNIPART/ROVER. Not aftermarket! These are .9375" bore size and were fitted to minis from 1959-64. One required per wheel and 2 per car set-supplied singly. Repair kit is GRK2013-This cylinder used 1/4" unf bleed...
Front to rear brake pipe, 101" in length. Includes male fittings on each end. Some early dry cars used a 103" pipe.
Easy bend copper 24"long brake pipe with one female and one male end for the regulator on the rear subframe to the n/s/r hose on hydrolastic cars only.
Also used on split front to rear system with valve in engine compartment - from 3 way uni...
These repair kits are for the later twin leading front drum brakes wheel cylinders GWC126/7 with .9375" bore size. The earlier twin cylinder set up used part number 8G8816 for GWC102/3 with 0.8125" bore size.
UNION FOR BRAKE PIPES IF YOU HAVE A DO IT YOURSELF FLARING KIT.
Set of 4 hoses, 2 front and 2 rear.
Braided brake and clutch hoses have a PTFE inner which helps to eliminate the spongy pedal feel under arduous conditions, and give greater efficiency. The outer braided stainless steel cover e...
Made in easy bend non rust material this one will fit the regulator valve on the rear subframe to rear hose on hydrolastic cars only as it is 8" long.
These pipes are retail less 35% discount at least to keep prices viable.
Copper easy bend 10" long metal pipe with male and female end fittings to fit between rear wheel cylinder and flexible hose on dry suspension models. These pipes are retail less 35% discount at least to keep prices viable.
1.4mm thick copper washer for all clutch and brake joint uses. This washer is 17.4mm wide with an 11.4mm diameter hole. Larger than a 233220A.
Easy bend copper pipe with 2 male unions 14" long which fitted most single line dry suspension cars from the brake master cylinder to the 3 way valve - the left hand drive version is 32"long - some people use the HF12 but originally it w...
Pair of front only braided steel hoses. Please be aware these are sided, the deeper internal threaded hose fits the right hand side, the shallower hose fits the passenger side.
These do not fit Portugese Mokes as they need 2 shallo...
Copper easy bend 6" long with a female and male end for fitting from the regulator valve on the rear subframe to the hose on the right hand rear. Dry suspension cars only as the hydrolastic uses HD8. Also used on late front to rear split...
We all believe that our life often depends on our braking system. But how can you tell when "it's good enough"? The flexible rubber brake hoses are a prime area for concern. The hose is both exposed to road grime (rain and dirt) but it is also expose...
Pair of steel braided rear hoses only. See C-AJJ4031B also for safer pro set up.
Brake line from RH brake hose union to the LH brake hose. 44" in length.
Also master cyl to servo for L/H/D which was 43" long.
see
21A42 for pre bent steel
10" long pipe with 2 male ends used on front drum brakes to join the wheel cylinders. Made in easy bend copper for long life. These kits or pipes are at least 35% off retail.
see 21A1206 for pre bent steel rh
Rear Braided brake hose set, with banjo union bolts and howver you need some tie wraps to hold hose to arms, runs from Radius Arm to Rear Cylinder, replaces both standard metal and rubber hose. No modifications are required and is of special interest...
Genuine Lockheed seal rebuild kit for Cooper S brake calipers. One kit needed per caliper. When it comes to safety critical parts, only fit the original suppliers' parts as repair kits. The kit includes all the seals needed to do both pistons in one ...
Genuine AP rear wheel cylinder with 3/4"(19mm) bore Lockheed double piston type as fitted to all cars from 1970 except "S". Includes bleed nipple, retaining clip and gasket.
Bleed nipple now 7mm spanner size but same thread-original [link]51...
These copper sealing washers should be replaced every time the hoses are undone as a precaution. 10mm i/d, 15mm o/d. is smaller than a 3H550
We all believe that our life often depends on our braking system. But how can you tell when "it's good enough"? The flexible rubber brake hoses are a prime area for concern. The hose is exposed to both road grime (rain and dirt) and also constant fle...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.