£59.99 exc vat
£71.99 inc vat
Out of stock
A great deal of timing scatter can be traced to a worn gear at the inside end of the dizzy drive but if yours has been lost or broken the 12G4499MS secondhand used units will get you out of trouble.
£59.99 exc vat
£71.99 inc vat
Out of stock
"used old"Distributor drive,all pre A Plus A series engines plus MGB.
Fitted in the engine block to drive the distributor these were made obsolete in 1988 by Rover so if you have lost yours we have a few of these used shafts to keep yo...
Water pump fitting kit for models without bypass facility, includes new bolts, washers and superseal gasket.
Big end shell bearings for the 1275 larger 1.75" diameter rod pin-not Cooper S
( Tri-Metal )
Sintered copper lead, lead plated,steel backed
Nominal Composition
Copper 74%
Lead 24%
Tin ...
Parts required to stop timing chain rattle on A plus engine with single row chain.Last chance to buy the plate and pin to hold the tensioner as they are
obsolete from Rover.
It is worth the expence to fit MSSK051EVOkit...
Spin on oil filter housing for performance engines-uses 88G402 gasket-made out of billet alloy it has a strong mating face to the block where oil leakage occurs from high revving engine vibrations, is slightly shorter offering more clear...
The last Rover update on the upper engine stabiliser bar, but this is upgraded for performance use.
A one piece silent block type bush, it was fitted at both ends from 1996 on and will fit any cars that had 2 bushes fitted at either end as o...
Mini Spares cam follower with original convex bottom Radii as used by BMC/Rover and made by Clanceys but less the oil hole. Using Clancey drawings and to our design for better cam performance and lift we have made the push rod recess deeper for stabi...
Genuine Mini Spares valve stem oil seal manufactured with original Dupont Viton, as fitted to the twin points engines, are the best material and seal you can use and although expensive are the best to date in stopping the engine smoking.
Man...
Original type engine lifting hook. Sold individually (2 required).
Fitted to all gold and some silver seal engine from the factory they were even found on original engines from the 1959 on era.
Set of +.030 thrust washers for 1275.Very useful for machining down when fitting non S cranks in 1275cc block
The breather can that goes on top of the clutch housing, '88 on, to clear servo.
Will also fit all earlier models.
Spacers for under the rocker pedestals are used mainly by engine tuners to allow tappet adjustment to be made where cylinder head mods have been carried out. 1.3mm/0.0512" thick, this can be used to hold locating screw on rocker post assembly but the...
woodruff key to fit in the camshaft to hold the larger timing chain gear. See 6K836 for the crankshaft keyway for the lower smaller timing chain gear
The little spring that sits at the end of a spring loaded carb needle on late HS and all HIF carbs where applicable.
This 5/8unf steel hexagonal head blanking plug was made for the inlet manifolds where the servo union can be fitted, plus blanking off the thermal transmitter hole under the thermostat. Uses 1B3664 washer ----------please note this will ...
A series mini engine crank pulley bolts have been known to come loose, caused by pulley damper vibration on competition engines. This is a high tensile longer extended thread cap head bolt with thick washer to rectify this problem and also allow furt...
Low drag 1275 piston standard size 2.780 (Rings included).
This piston has a possible compression ratio of 10.3:1 as fitted to Cooper RSP 1990.
The best performance 1275 pistons are C-STN100 range which have 9.73cr when the piston i...
Low drag 1275 piston standard size 2.780 plus 20 thou oversize(Rings included).
This piston has a possible compression ratio of 10.3:1 as fitted to Cooper RSP 1990.
The best performance 1275 pistons are C-STN100 range which have 9.7...
Rota slide adjustable duplex gear set.
The 2 wheels and chain weigh 1.379 kilograms and the cam gear is 680g.
Requires 2 x AEA687 countersunk screws (not included).
Cam gear bolts should be torqued t...
"Scatter Pattern" cams were designed by David Vizard to work best with the pecularities of the A-Series' siamese intake ports. The 310 scatter pattern is the ultimate race cam. Needs fully prepared engine for good results - high CR, high flow head, ...
20 thou oversize low drag slipper type pistons for modern day compression ratios and unleaded fuel.
Typically installation will result in a minimum 8.8:1 compression ratio but on some pre 1984 Metro versions it was higher.
Current...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.