£11.75 exc vat
£14.10 inc vat
In stock
The first Minis had a very simple gearchange, the lever exits the transmission directly through the floor. This requires a special boot to accommodate the curves in the floor and tunnel and being rubber it eventually cracks with age and flexing. Replace it with the real thing to keep wet or dry road crud out of the car. See 14A6861 for the metal surround to hold this gaiter in place.
£11.75 exc vat
£14.10 inc vat
In stockRecommended usage 1 x 14A6860 to fit one mini.
This is the round gaiter that stops the dirt getting into the gearlever on remote type boxes that had the magic wand gear lever fitted as a basic unit from 1968 on. It is not the gaiter screwed to the floor 14A6860.
about 21mm (...
The metal surround to complement the 14A6860 gear lever rubber gaiter on all very early minis with the long gear stick known as the magic wand type
Door panels in Red for MK1/2 doors less the fillets. This door panel design was used on all saloons & travellers from 1959 until 1970 when the door itself was redesigned. The panel slides into the door aperture and is held in place with a pair of doo...
Our lightweight underfelt kit is the perfect companion when fitting a new headlining. Made from lightweight felt and cut to size, this fits into the cavity of the roof before fitting your new headlining and provides increased sound insulation and pro...
The chrome moulding to fit the door bin on first 80 thousand MK1 minis with extra length tag with screw hole for location.
This is held on by screws but a single sided prong clips ADH3809 can be used in the centre - beware other...
Mk1 1962 on grey headlining that fitted on 2 hoop type frames whereas the Mk3 had individual rods. This is for Mk1 saloons only, see 5D4085 for cream crackle. (Does not include the framework).
These panels hold the door panels in place under tension inside the door aperture. It is not essential, but well worth replacing or renewing these in conjunction with new door panels. Sold in pairs.
Black door pocket liner for the R/H door which has sliding windows and external hinges
Black door pocket liner for the L/H door which has sliding windows and external hinges
Headlining kit including C post trims in cream crackle for 67-69 Minis which have a larger rear screen.
Cream with crackle finish sun visor fitted as standard from December 1965-69 but will fit Mk3 on if required. With mirror for passenger side. For a car set of clips see SV2021
Mk1/2 1965 on cream crackle SV2017C
Mk3 196...
bracket for boot board R/H on 7.7 gallon tank and on both sides for 5.5 gallon tank when 165 tyres fitted
Black with mirror, optional colour aftermarket sun visor for Mk3 models which were thinner than pre 1965 cars for safety requirements. Will fit cars from December 1965 on. Check out the special clips to hold these visors as they are sold seperately ...
Complete car set of roof lining rods, comprising of 1 Red, 2 White, 1 Black, 1 Blue and 1 Yellow
number 1 with red ends is EEB100060
number 2 and 3 is white ends are both EEB100070
number 4 with black ends is EEB100080
...
Similar to those fitted as standard on the late Coopers this piece of trimming is purely cosmetic although it may help to eradicate some road noise that might get past the standard rubber gaiter--This is black with red stitching.
Black sun visor less mirror that requires clips both ends but never a standard fitment colour fits cars from Dec 1965. Available as a sought after alternative to the cream colour. The brackets are available as a car set only(4 clips) as SV20...
This chromed bracket is to secure the early Mini sunvisor with the central location.
1959-64 visors had one central hinge and in October 1964-65 they fitted a sunvisor with a hinge one end and clip fixing the other-this is when the first pla...
This was the first style of sunvisor pad with central pivot point in cream crackle finish used on the early Minis.Some very early minis used pale grey for std but all Supers had crinkle finish cream to match headling. For this period the Cream Crackl...
This bag is made out of "Hardura" which is a heavy PVC with a felt backing laminated to it. When sewn up it will hold the Jack & lever and is all held with the tie Straps. Because the bag is made of heavy material it will not wear through unlike plas...
Ideal for solving the problem of fitting extra speaker's, this speaker board is simple to fit, and well finished.holes are oval shaped 6"x9"
Full carpet boot liner kit, completely lines the inside of the boot area.
Not suitable for MPI minis.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.