VALVE EXHAUST 31MM SHORT FOR COOPER S AEG163 CASTI...
AEG594

£36.23 exc vat

£43.48 inc vat

In stockIn stock
Exhaust valve. 1.22" (31mm) x 3.52"


As it is possible, even common, to swap one head for another on 1275 engines, it is quite easy to become confused, or worse yet, confuse the parts-guy when it is time to order new valves! Be aware that...

£36.23 exc vat

£43.48 inc vat

In stockIn stock

Recommended usage 4 x AEG594 to fit one mini.
Cylinder Head Cooper 'S' 970CC, 1071CC & 1275CC - Qty 4

People also bought products

New competition valve cotter for early heads with the large single groove valve, these are precision CNC machined from 4340 and heat treated to a better spec than EN24T and claimed to be stronger in fatigue life.

These locate better in the v...

New competition valve cotter, these are precision CNC machined from 4340 and heat treated to a better spec than EN24T and claimed to be stronger in fatigue life.

These locate better in the valves and easier to control spring heights.

Set of strong lightweight titanium top caps to suit our valve springs C-AEA526/527 hard for single collet competition valves. Sold as a set of 8.

Genuine Mini Spares valve stem oil seal manufactured with original Dupont Viton, as fitted to the twin points engines, are the best material and seal you can use and although expensive are the best to date in stopping the engine smoking.

Man...

160lbs on the nose at 400" for standard Cooper S or twin spring set ups. See C-AEA526 and C-AEA527 for later developed springs. These are ok for all standard uses but are improved and uprated over all original factory fitted...

Spacers for under the rocker pedestals are used mainly by engine tuners to allow tappet adjustment to be made where cylinder head mods have been carried out. 1.3mm/0.0512" thick, this can be used to hold locating screw on rocker post assembly but the...

1.259" (32.00) dia x 3.57 long Exhaust valve.


Our race valves are produced in EN214N steel. They are stellite tipped and use the later narrow, single collet groove and current valve head shapes.Heat treated to eradicate wear from unleade...

1.220" (31mm) dia x 3.57 exhaust valve.

Our race valves are produced in EN214N steel and are stellite tipped and use the later narrow, single collet groove and current valve head shapes.These valves are plasma heat treated to eradicate wear ...

1.401" dia x 3.52" long intake valves. Our race valves are produced in EN214N steel, stellite tipped and use the later narrow collet groove and current valve head shapes. As it is possible, even common, to swap one head for another on 1275 engines, i...

Genuine Mini Spares product as everything else on the market was poor fitting and unstable.

For Performance see 88G459EVO made in the USA by a Specialised Racing product company.

All the earlier heads used the 2A11 cott...

Actually 29.3mm (1.15") these valves are in EN214N steel with chrome plated stems for use in standard iron guides. Easily noticeable by their strange design shape they claim to give better flow characteristics.

If you drive A-Series cars long enough you will eventually have to replace the water pump bypass hose. These are the best quality available to fit without removing the cylinder head but these fluted rubber hoses have a bad reputation so if possible ...

Original type steel 'S' competition top caps for dual springs.

If you are upgrading from single springs or just want to replace those old worn top caps, these better grade material are the best answer. Eight required per head.

That tell tale puff of blue smoke when you first start is an indicator of worn guides or seals. Valve guides should be replaced with every valve job.

Sold individually, these are the original quality Cooper S guides for use in any head espec...

Made in EN214N steel and chrome plated for use with standard iron valve guides.

33.3mm (1.311") inlet valve easily noticable by there odd shape they are claimed to give better flow characteristics in standard or slightly modified engines.

Forged cast type rocker with original ratio of close to 1.3 with adjusting screw and 1/2" af nut. See AEG167, screw (regular) or AEG167EVO hexagon head); NT605061, nut - profile of pad reduces side loading on va...

If you want performance then you know you have to get as much air into the cylinder as possible. The bigger the valves the more this is possible. The standard 1275 mini and Sprite motor has only 1.3" intake valves, the standard Cooper "S" has 1.41" i...

1.158" (29.4) diameter exhaust valve for 12G940 casting.

Our race valves are produced in EN214N and plasma heat treated to eradicate wear from unleaded petrol. They are stellite tipped and use the later narrow, single collet gro...

1.158" (29.4) dia exhaust valve for 12G940 casting.

Our race valves are produced in EN214N stainless steel and require Manganese/Silicon bronze alloy valve guides. They are stellite tipped and have the triple collet groove and c...