CON ROD NUT "S" RACE ALTERNATIVE
EAC5541A

£2.25 exc vat

£2.70 inc vat

In stockIn stock
This alternative multi point nut was preferred by racers because the plastic locking part of the original AEG147 could fall out under extreme conditions on an over hot running engine. Current AEG147 are now an all metal nut with special gripping qualities. The built in flange of this latest specification multi point nut helps to spread the load and improve clamping force. sold singly 8 required per engine

£2.25 exc vat

£2.70 inc vat

In stockIn stock

Recommended usage 8 x EAC5541A to fit one mini.
Cooper 'S' 970ccc & 1070cc & 1275cc MK 1/MK2 - Qty 8
Cooper 'S' MK3 (12H397/12H398) & 12G Eng Nos. - Qty 8

Alternative products

These are made by ARP in the USA and considered the best available. This nut and bolt set also fit Sprite and Midget in line engines. Quantity required one kit per car. Torque up to 40-42lb ft.

Replacement for the original 'S' big end nut, this looks the same but is an up to date modern nut that grips on the thread replacing the plastic nyloc type.

The original plastic insert type, when under stress from very hot engines became lia...

People also bought products

Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).

Complete nut, bolt and washer set for engine to gearbox only

Water pump fitting kit for models without bypass facility, includes new bolts, washers and superseal gasket.

Complete fixing kit for a water pump, includes replacement silicone bypass hose, clips, superseal gasket, replacement bolts and washers.

later cars used this bolt to hold on the spin on filter head to the block-earlier cars used the CHS2613 stud--both are interchangeable

3/8"unc 1"long

There are 3 of these bolts fitted -1.75"long 5/16"UNF bolt ALTERNATIVE DAM7758.

Also used as longer bolt for water pump.

Also for the 21A1091 heavy duty tie rods on front suspension.

A series mini engine crank pulley bolts have been known to come loose, caused by pulley damper vibration on competition engines. This is a high tensile longer extended thread cap head bolt with thick washer to rectify this problem and also allow furt...

Longer main bolt stud.

As supplied with our main strap kit.

You require 5 of these high tensile short head studs and they torque to 42lb/ft. See also complete kit which includes these top grade studs C-AHT279. 3/8"unc stud with unf end for head nut and is 4" long. See other long head stud [link]C...

Special "S" main bearings nut set (6).7/16"AF thread

On all performance A series engines it is essential to ensure accurate and as near permanent location of the centre main bearing of the crankshaft as possible. Flexing allowed here, especi...

Fits all current range of oil pumps including GLP110MS.

Holds C-AHT54 oil pick up or standard oil pipe to case on outside of gearbox case 1/4"unf bolt 1.625"long

3 lengths of oil pump bolts have been used s...

The special washer under the tappet cover bolt.Sold singly 2 required per engine.

See 12A1176 for seal

1.75" LONG shouldered 1/4" bolt fits original concentric pumps plus some GLP139 and GLP110MS - check that you need a bolt this length as many later pumps require shorter bolts. This can of course be cut down or see [link]BH6...

Steel center main strap for small bore engines, comes with longer high tensile bolts. The Main bearing top cap will need machining flat, no other modifications required. Engine bolt hole centres all slightly vary from 2.775" to 2.785" - some 0.010" o...

Using new hardware makes any job more pleasant. If you're servicing your cylinder head you should examine the rocker studs for signs of stretching or stripped threads. Two long (51K885) and two short (51K1473) per head.

This is ...

This A type block 3/8" unc

stud to retain the cylinder head is 11/16"(17.3mm) longer than the standard 4" type with 1.5" of thread to hold brackets for other ancillaries such as coil. Usually fitted only at the heater tap end of the cylinde...

Engine stabiliser arm to block bolt. This is the longer bolt that fits the engine stabiliser rod to the cylinder block.

Fitted to the rear of engine blocks to drain out water these are now obsolete from Rover but available from us.1/4"bsp

3/8"unc 1.6250" long stud for engine block to accept the TAM2097 screw on filter head and for HS2 carbs, alternative to this is CHS2614 1.75" long and just over one thread longer. LYG10008 bolt was ...