(¥179) £179.25 exc vat
(¥215) £215.10 inc vat
In stock
If you have any doubt about the value of these panels- try having the rust and dents removed from yours! The double skin Mk2 type introduced in december 1966 is only available as Non Genuine, see8G9270MS We recommend fitting a boot board liner 14A9838
Need new cables for the boot lid? See 14A6740.
(¥179) £179.25 exc vat
(¥215) £215.10 inc vat
In stockRecommended usage 1 x 28G110MS to fit one mini.
Up until December 2003 we would have been embarrased to sell the only chrome
boot hinges available. They were bad fitting, looked poor quality and had so much play in them they were totally useless. But along came a set which does fit and is...
This liner was found on many deluxe Minis. The black fiberboard is held on by chrome screws and upholstery washers. Put it on any year Mini.
The original T shape boot handle as fitted to the bootlid of MK1/2 plus vans and estates except the wooden variety....
uses the ADA3817 type of seal, hole will need cutting to suit the shaft of the handle
These two simple cables are all that keep the boot lid from crashing down, damaging hinges, bumper and paint. When one fails we recommend replacing both to be sure of the same length. sold singly 2 required per car
37H3043 can be u...
Bootlid seal for Mini <91. Held in place on the boot lid using 26 clips(part# 14A6585).When fitting, the lip part of the seal open end for clips should face the inner boot catch- (the open end of the seal facing inwards to the bootlid al...
These gaskets should be changed when replacing the hinges-this one goes between the bootlid hinge on the bootlid. See also 24A2176 for gasket on body.
Used on all MK1/2/3 bootlids there are 26 little holes drilled around the inner edge to hold the seal on and this kit contains the 26 clips. For single clips see 14A6585. Later cars 1988 on fitted a seal to the body only. (CKE10018)
MkI aluminium boot lid "skin only" panel. This panel is produced off the original tooling, ensuring good panel fit and integrity. Following the pressing of the panel it is hand finished by Heritage craftsmen, to ensure the highest panel quality.
Threaded boss that fits in the floor of MK1 minis for the spare wheel clamp 14A6511 to screw into.
Not just a skin, but a complete MKI boot lid with inner skin. Lightweight, rustproof and well finished.
Very light, rustproof fiberglass boot lid SKIN. MKI replica with numberplate recess.
The boot floor (trunk of the Mini) has always been an area with a great potential to rust. Not only is it often exposed to battery acid but typically water collects there and rust results. BM Heritage produce a sub assembly from original tooling tha...
Used on all MK1/2/3 bootlids there are 26 little holes drilled around the inner edge to hold the seal on and this kit contains the 26 clips. For single clips see 14A6585. Later cars 1988 on fitted a seal to the body only. (CKE10018)
Full Mk1 door handle set with 2 front door locking handles and boot handle with matching keys.
These gaskets should be changed when replacing the hinges, this one goes between the bootlid hinge on the body, see 24A2175 also for upper on bootlid.
These gaskets should be changed when replacing the hinges-this one goes between the bootlid hinge on the bootlid. See also 24A2176 for gasket on body.
Bootlid seal for Mini <91. Held in place on the boot lid using 26 clips(part# 14A6585).When fitting, the lip part of the seal open end for clips should face the inner boot catch- (the open end of the seal facing inwards to the bootlid al...
Do not forget to replace this little rubber seal that stops water getting into the boot lid via the handle hole. For sliding window type cars the door locks use ADA3817.
On mk3 models the small door gasket on the Mk3 wind up window door hand...
These two simple cables are all that keep the boot lid from crashing down, damaging hinges, bumper and paint. When one fails we recommend replacing both to be sure of the same length. sold singly 2 required per car
37H3043 can be u...
Chrome plastic D shape type lamp fitted to many cars in the 1960s, the mini usually had two of these in black on the rear number plate of MK1/2 minis/vans and estates.
A metal version is available as BHA4153 and 83H335<...
This very heavy duty bonnet strap is a excellent reproduction of the original factory Special Tuning department special. Original light colour Tan leather
3.3mm thick from the tanneries for use on horse bridles, with alloy fastening. Screws ...
The original T shape boot handle as fitted to the bootlid of MK1/2 plus vans and estates except the wooden variety....
uses the ADA3817 type of seal, hole will need cutting to suit the shaft of the handle
This liner was found on many deluxe Minis. The black fiberboard is held on by chrome screws and upholstery washers. Put it on any year Mini.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.