(¥26) £26.30 exc vat
(¥32) £31.56 inc vat
Out of stock
this valve is longer than other A series varieties and plasma heat treated to eradicate wear from unleaded petrol.98.35mm total length. 3.879 "
The valves for the ...
(¥26) £26.30 exc vat
(¥32) £31.56 inc vat
Out of stock
37mm(1.457") longer inlet valve for the 2012 on 8 port head only
for use with special guides these are plasma heat treated to eradicate premature wear from unleaded petrol
3.933" 99.898mm long
Genuine Mini Spares valve stem oil seal manufactured with original Dupont Viton, as fitted to the twin points engines, are the best material and seal you can use and although expensive are the best to date in stopping the engine smoking.
Man...
Spacers for under the rocker pedestals are used mainly by engine tuners to allow tappet adjustment to be made where cylinder head mods have been carried out. 1.3mm/0.0512" thick, this can be used to hold locating screw on rocker post assembly but the...
Early Large cotter groove exhaust valve. Most small bore engines seem particularly prone to burning valves, it is highly recommended to replace the exhaust valves when you do a valve job! This 1.0" valve fits most early 948cc, 998cc and 1098cc engine...
1.220" (31mm) dia x 3.57 exhaust valve.
Our race valves are produced in EN214N steel and are stellite tipped and use the later narrow, single collet groove and current valve head shapes.These valves are plasma heat treated to eradicate wear ...
Genuine Mini Spares product as everything else on the market was poor fitting and unstable.
For Performance see 88G459EVO made in the USA by a Specialised Racing product company.
All the earlier heads used the 2A11 cott...
35.6mm(1.405") longer inlet valve for the original 8 port head pre 2012 spec only for use with silicon bronze guides these are plasma heat treated to eradicate premature wear from unleaded petrol.
The valves for the current 8 port heads from...
Original type steel 'S' competition top caps for dual springs.
If you are upgrading from single springs or just want to replace those old worn top caps, these better grade material are the best answer. Eight required per head.
For specialised race use only, these springs are 267lb@ 1/2"lift fitted.
(use C-AEA526 for race and fast road cams)
Modern high lift, short duration camshafts have posed quite a few problems for the general public in re...
Modern high lift, short duration camshafts have posed quite a few problems for the general public in recent years. Widely available performance valve springs were outdated overnight, as it became necessary to reduce spring crush. This, in turn, cause...
EN24 Nickel Chrome moly steel studs,Competition head stud kit.
torque to 45ftlbs -no need to re-torque cometic type head gaskets.
For use on the 2012 onwards heads only.
Complete stud, nut and washer kit for the cylinder head ancillaries. Kit contains parts to retain the following:
Inlet/Exhaust manifold to head, studs/nuts/washers
Thermostat housing (no sandwich plate) studs/nuts/washers
H...
Spring seat shims (set of 4), .030 thick (0.76mm).
Spacer shims to increase valve seat pressure and overall spring rate.
These were also used on all the 8 port head valve seats to prtect the alloy seats from wear. (8 port now C-AHT3...
Direct replacement rocker shaft. Fits all except full needle roller types. Far superior to the stock item! ENSURE YOU ALWAYS TIGHTEN DOWN ALL POSTS EQUALLY to eliminate stress fractures on shaft.
Our special "heavy duty" shaft has ...
Special thin type clip for fitting the water by pass hose between the water pump and the cylinder head. Most ordinary jubilee clips will not fit the tight area where the hose fits. Also used on C-AHH8537 oil cooler hose.
Payen stamped AF470, Standard composite reinforced gasket used on all large bore engines by Rover is an exceptionally good gasket. Asbestos free with special black sealing ring for the oil feed. Compressed volume is 4cc. This MINI head gasket has in ...
New colour, PB104 bronze guides.Although Silicon bronze valve guides were used for their extremely good wear values, they were very hard and not user friendly when fitting. These valve guides are recommended when using all EN21 4N stainless steel val...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.