(¥16) £15.96 exc vat
(¥19) £19.15 inc vat
In stock
(¥16) £15.96 exc vat
(¥19) £19.15 inc vat
In stockRecommended usage 1 x GDC102 to fit one mini.
for 23/25D distributor but see [link]47H5250[/link} for resin type upgrade with 3m of wire as opposed to every aftermarket type analysed with only 1.5m of wire.
its worth paying extra for the condenser and rotor arm [link]GRA101]/link]
Designed to fit the GDC102 side entry distributor cap as a protection against water, made in rubber.
Quickfit points for 23 & 25D4 distributors, keep a spare
BLACK HT SPARK PLUG LEADS TO FIT 23/25D DISTRIBUTOR WITH SIDE ENTRY CAP (GDC102).
7mm lead set
If you have an original 25D type distributor this is an upgraded arm (blade moulded and riveted )for performance use because all the other types available now are likely to fail at high revs. Because the blade is thin,or the rivet sometimes to long a...
If you want to tune your engine, or you have an engine for which there is no standard distributor available.....the new 123\TUNE is the answer!
123ignition is proud to announce the first fully programmable wireless ignition! Contr...
Electronic ignition conversion. For points type distributors, fixed or sliding. Negative earth only. Also, available for earlier 23/25D on Negative earth (LU142) or earlier 23/25D with Positive earth (LU142AP12).
ONLY use GCL217 coil for bal...
Pre A Plus Electronic Ignition distributor with vac unit, modified to our specification in the UK to give best performance on any minis with std to 276 camshaft profile.
Brand New distributor complete with electronic conversion already fitt...
Lots of things have been written about performance plug ignition wires but regardless of what you believe we all know that good wires are a must. This special competiton wires set from the Lucas factory has 8mm wire and the highest performance, no br...
Set of 4 ignition leads from the original supplier to Unipart, suitable for all twin point minis 1997 onwards. For use with M4 type coil.
original Lucas type RESIN BASED CONDENSER made for the 45/59D type distributor if you want a quality item rather than the cheaper inferior parts available. Filled with 3m of winding inside as per original Lucas but every copy analysed to date has ...
RESIN BASED CONDENSER as per the original Lucas type made for the 23/25D type distributor as fitted to original Cooper S or Racers who want a trusty part or where originality is required,with soldered wire connections and correctly made foot to sit ...
NEGATIVE EARTH ONLY..Reproduction CONTACTLESS Distributor suitable for modern day fuels for 850 and 998cc pre 1974 with upgraded rotor arm "Negative earth only". A worn out distributor can cost you both performance and economy. Precise spark timing ...
Electronic Distributor for any standard A+ 998cc. Negative earth only.
From 1982on 998cc were fitted with a ballast coil which means a new wire must be fitted from fusebox top left terminal where there is a large white cable to the...
NEGATIVE EARTH ONLY..45D electronic(contactless)Pre A plus distributor .
replaces 41824A and 41418 plus any 998/1098cc up to the changeover of A plus type distributors. For best performance and tune we advise our electronic evolution versio...
NEGATIVE EARTH ONLY. Cooper"S" 23D distributor, no vac unit-This is NOT THE ORIGINAL LUCAS ITEM but a new contact less electric copy of 40819 to cope better with modern day fuels. Fitted with the better Red rotor arm upgrade.Cheaper than many electro...
CSI-Ignition is a fully electronic ignition built in an original housing. You will have to remove the cap to see the difference! Neg earth only
After removing the cap you can select between 16 different curves by using
a screwdriver...
These are the screws needed to fix the condensor, points, base plate and vacuum to 45D and 59D distributors. For 23/25D type see 17H5106
These are the screws needed to fix the condenser, points and base plate to 23/25D distributors. See 57H5135 for 45D type distributors.
Replacement distributor cap retaining clip for all 45D type distributors-sold per clip.
the oil seal to fit on 12A1136 distributor housing. Pre A Plus
the earlier housing 2A612 did not have a seal.
If you have an original 25D type distributor this is an upgraded arm (blade moulded and riveted )for performance use because all the other types available now are likely to fail at high revs. Because the blade is thin,or the rivet sometimes to long a...
The all new 123 Electronic distributor is now available at Minispares. Featuring 16 ready programmed switchable advanced curves built in as standard, a must for any mini with a worn distributor. Full instructions are included with the system.For any ...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.