($6.45) £6.45 exc vat
($7.74) £7.74 inc vat
In stock
($6.45) £6.45 exc vat
($7.74) £7.74 inc vat
In stockRecommended usage 1 x 14A9785 to fit one mini.
The special pointed shape buffer locates against the boot board of Cooper S and variants where a factory type boot board is fitted.
The bracket fitted to the boot board and is not in any kits.
When a boot board is fitted the following brackets are required
14A9780x2 U shaped for the rear to hold the board
14A9781x2 side bracket with plug for board to si...
This kit contains all the floor brackets and mounts required for fitting Minis with 7.5 gallon tank 10/12" wheels or with 165 profile tyres.
The boot board bracket 14A9783 is not included
For 10" wheels with 145 tyres ...
bracket for boot board R/H on 7.7 gallon tank and on both sides for 5.5 gallon tank when 165 tyres fitted
L/H BOOT BOARD SIDE BRACKET FOR 7.5 GALLON TANK.
boot board 32" wide for early cars with smaller 5.5 gallon tank
For 7.5 gallon petrol tank cars this is 29" wide with one corner cut. If you are looking for an alternative to this carpet covered wood boot floor, try our plastic load liner EBF100150
The chrome moulding to fit the door bin on first 80 thousand MK1 minis with extra length tag with screw hole for location.
This is held on by screws but a single sided prong clips ADH3809 can be used in the centre - beware other...
Tank strap bracket welded to the rear of the boot floor which the single diagonal tank strap 21A2838 attaches to.
Taller centre boot board bracket for when wider 165 tyres are fitted to the spare wheel. Supplied with the rubber and pin.
Threaded boss that fits in the floor of MK1 minis for the spare wheel clamp 14A6511 to screw into.
Used on all MK1/2/3 bootlids there are 26 little holes drilled around the inner edge to hold the seal on and this kit contains the 26 clips. For single clips see 14A6585. Later cars 1988 on fitted a seal to the body only. (CKE10018)
MK1/2 interior door handle with screw and washer.
This solid "spoon" handle is brittle and easily broken.
These are the original shape as sold under the Unipart label, not the later Rover bagged item which was a reproduction with d...
Reproduction gear lever gaiter for all remote control type gearboxes with the short gear lever by the driver's seat. The metal retainer for this gaiter is 14A9942. These were fitted until the introduction of the rod change type [link]CZH...
These gaskets should be changed when replacing the hinges, this one goes between the bootlid hinge on the body, see 24A2175 also for upper on bootlid.
These gaskets should be changed when replacing the hinges-this one goes between the bootlid hinge on the bootlid. See also 24A2176 for gasket on body.
Bootlid seal for Mini <91. Held in place on the boot lid using 26 clips(part# 14A6585).When fitting, the lip part of the seal open end for clips should face the inner boot catch- (the open end of the seal facing inwards to the bootlid al...
Seal for door handles MK1/2 and all sliding window exterior hinge cars.
also used on 14A7195 mk1 boot handlle used on mk1/mk2 and van/estate
is oval shaped
for boot / rear door use the hole at the rear ...
GT emblem stick on logo for use on gearlever knobs and key fobs sold by us.
about 27.4mm wide, please note these are now black and silver not black and gold.
Chromed version of the standard demist vent on early cars where the ashtray is
mounted in the top and middle of the metal facia. Not for later cars with large
padded windscreen rails and ashtray in the front such as Mini Clubman and...
This polished aluminium corner plate fits over the leading edge of the MKI/II door pocket to add protection and class. Only the Nearside plate is supplied.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.