($6.00) £6.00 exc vat
($7.20) £7.20 inc vat
In stock
($6.00) £6.00 exc vat
($7.20) £7.20 inc vat
In stockRecommended usage 1 x 17H3723 to fit one mini.
Genuine plastic cap as supplied on single line brake cylinders pre 1976 and all clutch masters.
It doesn't often break or wear out but it gets lost or turns yellow. The early steel master cylinder reservoir caps had a tendency to rust on, so...
Correct flat top brake master cylinder for pre 65 Cooper S.
Originally the top of this master cylinder would have had either a removable union or a small hexagonal nut shape machined into it, but neither of these options are available so the...
Seal for between the brake servo and master cylinder, fits all late 1988 onwards vehicles where the master cylinder was mounted directly to the servo unit.
Master Cylinder repair kit for repairing the late GMC90376 master cylinder that was attached to the servo from 1995 until the end of production this kit uses a longer seal in conjunction with a nylon bearing. If your master cylinder has a drill hole ...
NOTE: DOES NOT COME WITH THE SWITCH - HAS A BLANKING BOLT FITTED
The last diagonal brake split models had this square plastic canister (reservoir). With metric unions it's recognised by the rectangular reservoir and small cap with ...
Large diameter cap, with seal, as used on dual-line brake master cylinders.
Genuine AP. The only master cylinder cap with a spade terminal on it which is for your brake fluid safety warning. This is AP latest and current offering in GREY as it is a superior cap, although a third cheaper than the white cap they deleted. Bewar...
Original AP Lockheed type metal body master cylinder.
Fitted with a plastic cap the metal original alternative is available seperately as 17H5323
Ensure the correct DOT4 or DOT5.1 brake fluid is used as these cylinders...
Almost every Mini built prior to the dual circuit system uses a .70" bore master cylinder. This kit fits them all. The original size in the '59-'64 Mini was .75" but as most of these cylinders have been replaced with the .70" size it is best to check...
Genuine AP Master cylinder with plastic tank.
The master cylinder is the heart of any hydraulic system and the hardest to troubleshoot. A pedal that can be slowly pushed to the floor indicates the master cylinder is worn. Fluid dripping off ...
Genuine AP Lockheed boxed - Made in UK - fitted from 1988 on, this master cylinder uses a built in servo.
This master cylinder was used right up to the last production twin point vehicles from Rover. Bore size is 20.6mm(.811").
See ...
This twin line brake PDWA valve is fitted on the front bulkhead of the engine bay from 1978 on as opposed to the single line valve which was fitted on the rear subframe.
Fixing bolt is 2.25" long UNF 1/4. The 4 Brake unions are all metric. ...
Genuine AP Lockheed boxed and made in UK. FRONT TO REAR master is the latest model dual master cylinders, which was introduced in 1985 with a stepped bore of 17.8 to 19mm to replace any previous master cylinders from September 1978 to 1988 when the b...
These repair kits are for the early twin leading front drum brakes wheel cylinders GWC102/3 with .8125" bore size. The later twin cylinder set up used .9375" size part number GRK2002.
Please note however - if your cylinders are...
If your wheel cylinder does not bolt on it uses this special clip. Some new wheel cylinders come with this clip included so check on ordering.
5/8" bore-Fitted to all Cooper 'S' hydrolastic cars from Sept 1964 plus mini to 1967.Also used from 1959-1963 and intermittently on. Leyland used this smaller type cylinder with servo on disc set ups as standard.
Bleed nipple now 7mm spanner...
Non genuine 0.625-5/8" reproduction rear wheel cylinder used from 1959-1967.
Quantity one per rear wheel and 2 required for car set.
Bleed nipple now 7mm spanner size but same thread-original 513118A used to be 6.2mm (1...
Twin leading shoe brakes use two wheel cylinders per wheel, but you buy them singly. These cylinders are the 15/16" diameter style that will fit MK1/2/3 models 1964 on with .9375" bore size with 1 1/2" shoes.
Sold with bleed nipple but requi...
Rear wheel cylinder with 0.6875" bore size first appeared in 1974 on single line 1275GT cars and then on some split diagonal until 1976--also fitted to Innocenti cars when they had a unique 4 way swith union--- repair kits for these cylinders are [li...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.