CRANK BOLT LONG CAPHEAD WITH AND SPECIAL WASHER
C-AHT147

($8.91) £8.91 exc vat

($10.69) £10.69 inc vat

In stockIn stock
A series mini engine crank pulley bolts have been known to come loose, caused by pulley damper vibration on competition engines. This is a high tensile longer extended thread cap head bolt with thick washer to rectify this problem and also allow further spacing of the pulley. 0ver 2,500 sold since 1999. Requires 1/2" hex key part number TOOL22.

($8.91) £8.91 exc vat

($10.69) £10.69 inc vat

In stockIn stock

Recommended usage 1 x C-AHT147 to fit one mini.
Water Pump, Pulleys & Ancillaries - Qty 1

Recommended products

1/2" hex key socket needed when using our upgraded crank pulley bolt C-AHT147, 1/2" drive.

Alternative products

The head of this crank bolt has a large identification hole. Used for all pulleys with vibration type damper--For pre A plus see AEA312 but -see also our special bolt and washer C-AHT147 which fits all known crankshaft threa...

Kit products

A full kit to convert your timing gears to a belt driven type to restore power loss caused by original timing gear wear and stretching. Also helps reduce noise associated with valve train and dampen out certain harmonic noises generated by the 3 main...

Replacing the original camshaft timing chain with a belt was a giant step forward. Now with improved metallurgy for the gears and use of a plastic housing we have probably reached the ultimate - highest quality with the lowest weight. The adjustable ...

People also bought products

Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).

Complete nut, bolt and washer set for engine to gearbox only

Water pump fitting kit for models without bypass facility, includes new bolts, washers and superseal gasket.

Complete fixing kit for a water pump, includes replacement silicone bypass hose, clips, superseal gasket, replacement bolts and washers.

later cars used this bolt to hold on the spin on filter head to the block-earlier cars used the CHS2613 stud--both are interchangeable

3/8"unc 1"long

There are 3 of these bolts fitted -1.75"long 5/16"UNF bolt ALTERNATIVE DAM7758.

Also used as longer bolt for water pump.

Also for the 21A1091 heavy duty tie rods on front suspension.

Longer main bolt stud.

As supplied with our main strap kit.

The high tensile bolts supplied with the 998 centre main strap kit.

You require 5 of these high tensile short head studs and they torque to 42lb/ft. See also complete kit which includes these top grade studs C-AHT279. 3/8"unc stud with unf end for head nut and is 4" long. See other long head stud [link]C...

Special "S" main bearings nut set (6).7/16"AF thread

On all performance A series engines it is essential to ensure accurate and as near permanent location of the centre main bearing of the crankshaft as possible. Flexing allowed here, especi...

Fits all current range of oil pumps including GLP110MS.

Holds C-AHT54 oil pick up or standard oil pipe to case on outside of gearbox case 1/4"unf bolt 1.625"long

3 lengths of oil pump bolts have been used s...

Special bolt that fits the engine front plate to support the adjusting link for alternators/dynamo

The special washer under the tappet cover bolt.Sold singly 2 required per engine.

See 12A1176 for seal

1.75" LONG shouldered 1/4" bolt fits original concentric pumps plus some GLP139 and GLP110MS - check that you need a bolt this length as many later pumps require shorter bolts. This can of course be cut down or see [link]BH6...

Steel center main strap for small bore engines, comes with longer high tensile bolts. The Main bearing top cap will need machining flat, no other modifications required. Engine bolt hole centres all slightly vary from 2.775" to 2.785" - some 0.010" o...

Using new hardware makes any job more pleasant. If you're servicing your cylinder head you should examine the rocker studs for signs of stretching or stripped threads. Two long (51K885) and two short (51K1473) per head.

This is ...

Engine stabiliser arm to block bolt. This is the longer bolt that fits the engine stabiliser rod to the cylinder block.

Fitted to the rear of engine blocks to drain out water these are now obsolete from Rover but available from us.1/4"bsp

This alternative multi point nut was preferred by racers because the plastic locking part of the original AEG147 could fall out under extreme conditions on an over hot running engine. Current AEG147 are now an all metal nut ...