LOWER ARMS. ON CAR ADJUSTABLE
C-AJJ3360

($54.40) £54.40 exc vat

($65.28) £65.28 inc vat

In stockIn stock
Ultimate lower arm for road or race. (pair supplied)

One piece, forged, fully adjustable on the car lower arms (with knuckle for bushes) to allow adjustment for any camber setting required. Sold in pairs only. It is recommended that you fit C-STR631/2 offset bushes for true geometry checks.

Discard the eyelet for the bushes and you can fit spherical joint/rose joint ends for race use. Makes all other arms obsolete. When increasing negative canber ST Abingdon always advised fitting a 3mm plate under the top arm where the bump stop 2A4267 hits to prevent undue strain on the driveshafts.

($54.40) £54.40 exc vat

($65.28) £65.28 inc vat

In stockIn stock

Recommended usage 1 x C-AJJ3360 to fit one mini.
Front Suspension - Qty 1
Front Suspension, Hubs, Upper and Lower Arms - Qty 1

Recommended products

Mini Spares Non genuine a re-bound buffer which is the same as Rover Xparts are supplying as genuine. Fitted purely to prevent the top arm crashing in to the subframe on full droop (as when airborne),and stopping the suspension ball joint going bound...

Longer track rod end for running with negative camber, gives an extra 5mm of adjustment approximately over the standard item. Has consistent thread pattern and perfect design to our requirements to fits all known racks and classed as a competition tr...

Mini Spares product UK made especially for use when geometry has been changed, such as fitting adjustable tie rods or lower arms, or on any cars with corrected castor angles.

Set of 4 bushes.

These metal sleeved bushes are specially...

A must-when the castor and camber angles are changed or whenever the geometry of the car is set up you will require these bushes. They are good for cars with up to 3.5 degrees of castor angle.

From November 2003 they have been made from a s...

Genuine X parts -the same as our 2A4267MS Re-bound buffer which are fitted purely to prevent the top arm crashing in to the subframe on full droop (as when airborne), and stopping the suspension ball joint going bound in full droop. It <...

Alternative products

Performance geometry kit includes tie bars, lower arms plus performance bushes for lower arms and tie rods. This is basicaly the same kit as MSSK3013 but less the rear tracking and camber brackets.

parts in kit to transform hand...

Kit products

SAVE 25%-Geometry kit, same as MSSK3013 but without the correct special rubber bush kits.This kit saves over 25% on cost of individual parts.

This kit is for customers who wish to fit their own choice of bushes but

Mini...

Performance geometry kit includes tie bars, lower arms plus performance bushes for lower arms and tie rods. This is basicaly the same kit as MSSK3013 but less the rear tracking and camber brackets.

parts in kit to transform hand...

Ultimate road damper and geometry kit which includes following parts. A set of AGX Evolution dampers with hilos plus adjustable tie rods and lower arms with the correct bush kits. For the rear a set of camber and tracking brackets. when fitted the su...

Ultimate road or race geometry kit which includes following parts. Adjustable tie rods and lower arms with the correct bush kits. For the rear a set of camber and tracking brackets. When fitted the suspension must be properly set up. This kit will dr...

one piece forged lower rod end arms

unbelievably at this price they are not the welded type as sold by many of our competitors

Same as the C-AJJ3360 lower arm kit, but includes the spherical rod ends,spacers and dustcov...

Ultimate Front geometry kit which includes following parts. Adjustable tie rods and lower arms with the correct bush kits. When fitted the suspension must be properly set up. This type of kit allows you or the person setting your rear suspension up a...

Ultimate road damper and geometry kit which includes following parts. A set of AGX Evolution dampers with hilos plus adjustable tie rods and lower arms with the correct bush kits. For the rear a set of camber and tracking brackets. When fitted the su...

Ultimate geometry kit for competition use which includes following parts. Adjustable tie rods with Mini spares tie bar bush kit (not spherical joints) and Spherical jointed lower arms with the dust covers. For the rear a set of camber and tracking br...

People also bought products

Genuine Mini Spares standard performance cone utilizing 20 years of elastomer/rubber technology from our competition cones manufacturer. Only beeen available since 02/09/2020 and proudly made in the UK with 10,000 sold by 2023.

Original cone...

Genuine Mini Spares UK made complete joint with the following specifications,

correct dimensions and shape of pin and ball in EN24T, using correct spec grease,

genuine original shape cup using correct material (21A423MS...

Genuine Mini Spares UK made joints are complete with the following specifications, correct dimensions and shape metal knuckle in EN24T, with the genuine cup made in original material and correct shape (21A423MS) and an upgraded poly boot...

Standard gas filled replacement front shock absorber from Bilstein.



Non hand adjustable front damper guide ratings

442001 KYB standard replacement

342001 KYB Gas filled 25% upgrade on sta...

Replacement ball joint shims, comprising of 2x 003"(.076MM) shims, 2x 005"(.127MM) and 2 x 010"(.254MM).

Tie rod extra hard rubber bush, harder than standard.

You dont want these bushes too hard as it can cause the threaded on the end of the tie rod to break under extreme conditions.

In theory the outer ones should be harder for rigidi...

Mini Spares quality suspension kit includes all four adjustable alloy trumpets and knuckle joints plus the two extended rod struts required for the rear. Many people will advise you, why you should consider upgrading to the genuine classic "Hi/Lo" su...

Car set of 4 top Subframe tower mountings for Road cars from 1976-2000.

Aluminum pad for the top of each subframe mounting and a poly pad below to replace the standard rubbers originally fitted. The alloy pads help reduce subframe movement, ...

extra parts required to convert the C-AJJ3360 lower arms to spherical rod end type if the arms were previuosly purchased-These parts are available with the arms as C-AJJ3360A as a money saver

one piece forged lower rod end arms

unbelievably at this price they are not the welded type as sold by many of our competitors

Same as the C-AJJ3360 lower arm kit, but includes the spherical rod ends,spacers and dustcov...

The New Front Evolution AGX shock absorber is twin tube type and gas filled. On car 8 point easy adjustable specific settings. This is currently one of the shortest fitted length dampers we stock. Closed length 210mm from pin centres. Open length is ...

Genuine Mini Spares product ideal for road use for maximum performance, where other examples available tail off as they get worked and heat up.

Hilos will be required to enable fitment as they are taller but FAM3968EVO are a str...

Lower suspension arms to give 2.0 extra degrees of negative camber. Stamped with 2.0 Sold in pairs only.


General:See also c-AJJ3360 fully adjustable arms

Negative camber lower arms are specifically forged in different degrees to...

Angled grease nipple for the upper arm on the front suspension of all Minis

importantly lubricates the upper arm spindle which so often gets neglected so check yours out and make sure this nipple is working properly. Also fits rear radius ar...

Lower arm top hat bush in poly to fit all lower arms with twin taper as standard from 1965. Mini Spares have upped the game once again with these superbly finished bushes which surpass anything on the market. Fitted with a metal bush insert these are...

A must-when the castor and camber angles are changed or whenever the geometry of the car is set up you will require these bushes. They are good for cars with up to 3.5 degrees of castor angle.

From November 2003 they have been made from a s...

Genuine Mini Spares part improved from original for the R/H upper mounting point of your damper(shock absorber) and fit 14A6948 captive nut plates for upper bolt fixings . For lowered suspension use C-AJJ3359

These cone springs will require Hilo adjustable suspension as they sit higher than the originals.Containg an anti fade property and shape which helps them going off during racing and giving hopefully a season of racing before replacement. A softer ro...

Uses 2 Soft standard rubbers on the insides and the 2 Mauve poly on the outside.

HARD OUTERS / SOFT INNERS - STOPS BRAKE WEAVING.

Don't be confused as this special shore hardness set up was proven after 2 years of testing and is per...

Lower arm bush for pre 1966 cars. The lower arm had a straight hole whereas the later cars from 1966 on had a tapered hole and used 21A1882 bush with a metal sleeve in. This bush has no inner sleeve and it was discontinued in 1966. Sold ...