($44.80) £44.80 exc vat
($53.76) £53.76 inc vat
In stock
($44.80) £44.80 exc vat
($53.76) £53.76 inc vat
In stockRecommended usage 1 x C1072-20 to fit one mini.
3 compression ring @ 0.625" and single one piece oil ring 0.125 as per original 998 pre A plus and 1098cc versions inc morris minor and sprite range. Also available is a high grade ring set c-STN99-20 with 3 piece oil ring
Replace with new camshaft,it's almost too easy to overlook during a rebuild. Camshaft bearings are pressed into the block and thus are usually done by a machine shop. You would not rebuild an engine without replacing the rod bearings, so why not the ...
Special superb extra strong timing chain with very limited stretch using modern day materials and technology to keep your timing correct and will fit any A series engine using a single row chain.
This chain saves all the time and effort requ...
Complete fixing kit for a water pump, includes replacement silicone bypass hose, clips, superseal gasket, replacement bolts and washers.
woodruff key to fit in the camshaft to hold the larger timing chain gear. See 6K836 for the crankshaft keyway for the lower smaller timing chain gear
Genuine Mini Spares Klinger timing chain gasket for any BMC A series engine with 10 gasket holes, fitted until the introduction of the A plus type which had a bulge in its side where the tensioner was fitted which had 11 holes.
The klinger m...
ACL Main bearings for the crankshaft as preferred by performance engine builders 10 thou oversize pre 1985
Sintered copper lead, lead plated,steel backed
Nominal Composition
Copper 74%
Lead 24%
RUBBER CHAIN TENSIONER (2 PER CAR) FITS WITH WIDE GEAR ONLY.
Sold singly 2 required per engine.
Converted into a non melting type grease.Favoured by proffessionals for camshaft,lobes and lifter,and any valvetrain to stop scuffing on start up. Also useful for oil pumps to stop drain back on start up
The screw that holds the drum on the hub. Earlier hubs had two screws, many replacements have only one, all that’s needed.
Probably the most used jointing compound used by mini owners for nearly every gasket except the cylinder head. Some late minis used a silicone jointing compound instead of gaskets on the differential, see GAC8000.
These can get really cooked behind the exhaust manifold, if you're oozing oil it may be time to replace them. Sold singly 2 required per engine
Mini Spares own Universal gasket set for solid wall blocks
For any manual block, includes gaskets for "A"Plus and pre A Plus timing covers, but is less tappet chest cover gaskets. Does not include clutch oil seal.
We now offer an en...
Convex type core plug at 41.4mm for all early A series blocks up to A plus.
4 required per engine-these are known as the flat type wher the centre has to be pressed in so the convex plug spreads out. The Cooper S althouh same size was a cup ...
Good maintenance, just as you would never rebuild your motor without replacing the crank thrust washers, you should also care about the camshaft thrust plate. Sometimes called the "triangle plate" this small but important plate doesn't just hold the ...
Keyed or cupped, either variety does the job. A plus engines use a TAM2020.
Genuine Mini Spares best selling super upgraded Klinger gasket set for any popular engine block.
So called genuine Rover gasket sets were so poor in quality or have incorrect parts we decided to put together our own correct real gasket set u...
Rod bearings, 850-1275 1 5/8" journals. Heavy duty steel backed bearing for durability and long life. The bearings to use if you want it to last. The only bearings to use on a fast road motor.
( Tri-Metal )
Sintered copper lead, le...
LOCKTAB FOR CON ROD BIG END BOLTS ON SMALL BORE A SERIES ENGINES.
Very important shim to go behind crankshaft timing gear to align both wheels up and get correct alignment/true running of timing chain. Approx 5 thou thick, fit as many shims as required.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.