($185.17) £185.17 exc vat
($222.20) £222.20 inc vat
Out of stock
($185.17) £185.17 exc vat
($222.20) £222.20 inc vat
Out of stock
handbrake handle in Burr walnut to compliment the wooden dashes.
The inside is rough finished and depending on year of car tape will have to be
used on the lever to make this a snug fit.
See also MSA0193 door ...
Walnut Burr gear lever knob.
Standing 4 inches tall and carved from billet burr walnut, it really makes a statement. It has a Mini winged logo pattern embossed.
door window winder handle pair in Burr walnut finish to compliment the wooden dashes.
If your old screws do not fit see G285
See also MSA0193 door opening handles, MSA0191 door cappings and MSA0192...
Lovely Burr walnut dash for left hand drive cars with 3 clocks in front of driver.
2 outer rings and 2 inner knobs which have to be stuck on.
Chromed version of the standard demist vent on early cars where the ashtray is
mounted in the top and middle of the metal facia. Not for later cars with large
padded windscreen rails and ashtray in the front such as Mini Clubman and...
The black plastic pod which mounts the speedo and two gauges in the original central position. In the 1970's and 1980's a great number of Mini owners caught the customizing bug and a lot of Minis had custom dashboards installed. Now we're going the o...
The black vinyl covering that lays on your lower dash shelf. For cars after 1970 where the facia panel is not a full metal panel you must fit (link)DT3076(/link)
ALSO SUITABLE FOR EARLY MK3 CARS THAT RETAINED THE DASH MOUNTED STARTER SWITCH AND TOGGLE SWITCHES CARRIED OVER FROM THE MK2 CARS.THE CHROME TRIM FOR THIS IS ALA6640
Fitted for safety regulations to all MK2 minis from 1967-80 except Sweden and Canada to 1975 (not any MKI or van and pick up). Later commercial type minis did have it fitted with 3 clock speedo pod. This is a hard foam pad at the lower edge of the pa...
Ashtray that sits in the upper padded dash on all vehicles with 2/3 clocks positioned in front of driver. Early cars had flat plastic tray face whereas later cars had crinkly type face which is the only type available- They all fit the same.
Dash liners with air vents for on de luxe versions with centre speedo and two gauges which are black vinyl covered as opposed to the painted type. Not for the single centre clock only. The cardboard is cut out but the vinyl needs trimming when fittin...
Late type swith carrier with 4 square holes plus heater and choke cable holes-uses the ratchet type choke cable with D shape fitting--earlier cars used round hole for pull and push chooke cableCZH3591
FIA spec anchor plate for eye bolts, used when fitting harnesses. Sold individually, 7/16 UNF 65x65x3mm.
Plain white with white backing aftermarket sun visor as fitted to Mk3 models 1977-92 which were thinner than Mk1 for safety crushing requirements. Although not standard for earlier models will fit cars from December 1965. Check out the special clips ...
Light grey plastic 6" mirror fitted by BMC as standard from October 1964-69.
The first light grey plastic 6" mirror with a twin ball stem and black sucker was patented in 1962 but not fitted until October 1964. At the end of 1965 the twin ba...
Eye bolt for harness mounting. sold individually, 7/16 UNF.
Complete car set of roof lining rods, comprising of 1 Red, 2 White, 1 Black, 1 Blue and 1 Yellow
number 1 with red ends is EEB100060
number 2 and 3 is white ends are both EEB100070
number 4 with black ends is EEB100080
...
'Walnut Burr gear lever knob.
Standing 3.5 inches tall with a shape that is comfortable to the hand it really makes a statement. the old original type with a logo has been made obsolete owing to royalty and intellectual agreements held by Ro...
Ideal for solving the problem of fitting extra speaker's, this speaker board is simple to fit, and well finished speaker holes are oval 6"x9"
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.