($57.60) £57.60 exc vat
($69.12) £69.12 inc vat
($57.60) £57.60 exc vat
($69.12) £69.12 inc vat
Recommended usage 1 x GEX33519 to fit one mini.
2 reqd but sold seperately-From 1990 rover started fitting the hanging rubber exhaust mounting straps which push onto rods on the exhaust and rear subframe similar to the old metro. These were used right to the end of production on minis.
Rear RC-40 fitted with a pipe to bolt straight on to the catalyst for cars built late 1991 onwards (not early carb coopers). It has the hanger rods fited for mounting onto the rubber type straps. This makes it a single box system with a little throat...
Rear RC-40 twin box system to fit catalyst for cars built late 1991 on SPI(not early carb coopers). It has the hanger rods fited for mounting onto the rubber type straps. This makes it a twin box system with a little throatier pleasing note, but a mu...
Exhaust manifold to downpipe clamp. For 32mm o/d pipe size.
The key to eliminating exhaust leaks at the manifold flange is the clamp. These cast clamps are the best style to use. A real piece of kit to use eradicating a multitude of likely p...
Exhaust manifold to downpipe clamp.
The key to eliminating exhaust leaks at the manifold flange is the clamp. These new clamps include proper brass nuts and support washers. Fits most 850cc, 948cc, 998 etc. Those engines with single carb an...
downpipe from the exhaust manifold on the petrol 1275cc Ritz and Italian Job mini 1991/3 which had the 1.5" HIF38 carb. The automatic version of this down pipe is GEX12054
The original replacement is expensive so when it needs replacing many customers
opt for our stage one kit C-STN22 which gives extra power for litle more cost.
in this kit you will get an exhaust manifold, which is bette...
Twin box exhaust system for all 850/998/1100 saloons
Now designed by our RC40 team as a 2 piece system for easier fitment and transportation, this fits from the original cast iron inlet/exhaust manifold
right to the rea...
1.75" Bore centre exit twin tail pipe maniflow rear box with adaptor to sleeve down to the standard mini 998cc type exhaust system.
The very rear bobbin type mounting rubber on every mini made until the introduction of a rubber hanger strap in 1992. When the RC40 or similar systems are fitted, 2 will be required. This is a stronger poly version.
Rear RC-40 twin box system to fit catalyst for cars built late 1991 on SPI(not early carb coopers). It has the hanger rods fited for mounting onto the rubber type straps. This makes it a twin box system with a little throatier pleasing note, but a mu...
Blanking plug to blank of the Lambda sensor hole on all SPI/MPI models.
M10 metric flanged bolt 35mm long for catalytic converter. (4 required per unit)
This sleeve will allow an 1"3/4 rear box to fit a standard bore front pipe of a 998cc mini. The large end fits into the RC40 and the smaller end accepts the 1.25" diameter as standard 850/998 exhaust pipe bore
Part of our millennium range of exhausts, this is the 200 Cell sport cat.
Catalytic converter will fit all mini models and if you require new studs the part number is FB110351 and the nuts to fit the studs are NV110051<...
The original design flare (pinch) shaped silencers on this twin box exhaust system will fit right onto either the original Cooper S exhaust manifold/header or the Cooper Freeflow manifold. In stock for the first time in years!split into 2 parts for ...
THE M10 METRIC NUT THAT SCREWS ON THE THREAD BOLTS OF THE CATALYLITIC CONVERTER
The famous RC40 Millennium range mild steel Standard bore centre exit exhaust plus the fitting kit for the exhaust system.
Exhaust centre strap that hangs from the mounting on the centre of the rear subframe, for saloon models only as the van is longer(GEX7273).
The clip on the exhaust that this attaches to is GEX7052 and is usually on a new exhaust...