SEAM MOULDING CLIP
GFK7515

($0.12) £0.12 exc vat

($0.14) £0.14 inc vat

In stockIn stock
Zinc plated mild steel clip for fixing vertical seam mouldings to the body.

($0.12) £0.12 exc vat

($0.14) £0.14 inc vat

In stockIn stock

Recommended usage 20 x GFK7515 to fit one mini.
Van, Estate and Pick up Floor - Qty A/R
Wheel Arches and Mouldings - Qty A/R

Alternative products
SEAM MOULDING CLIP STAINLESS STEEL
BMP128MS

These are the clips that hold on the vertical seam mouldings on all minis.

The original metal type are prone to rust so Mini spares producedd these stainless steel versions which are also cheaper. Supplied as a single clip, order as many as ...

($0.28) £0.28 exc vat

($0.34) £0.34 inc vat
MILD STEEL SEAM MOULDING CLIP
BMP128

These are the original Rover Xparts clips that hold on the vertical seam mouldings for all minis, prone to rust this was Rovers upgrade but Mini spares produced a stainless steel version BMP128MS which is also cheaper and a better option...

($0.50) £0.50 exc vat

($0.60) £0.60 inc vat
People also bought products
RIVET CLIP UPPER DOOR MOULDING (BOTTOM)
13H744

Upper door moulding rivet for Cooper S door trim. For Mk1 usually 1 at front and 3 at back making 4 per side and on Mk2 there were 2 per end at bottom making 4 per side. This is the 10mm head rivet and not required on our own 14A9773/9774 trims that ...

($0.83) £0.83 exc vat

($1.00) £1.00 inc vat
SPORTS PACK ARCH FIXING STUD ORIGINAL TYPE
KLMP4402

Stainless steel stud for original production factory fitted sports pack arches.

These use FN105047 nuts.

New genuine arches now have an upgraded threaded brass insert and now use a stud ZUA000250.

($4.73) £4.73 exc vat

($5.68) £5.68 inc vat
BLACK DELUX MOULDED SILL TRIM
GZF108A

Fluted type equivalent of GZF105A. This is equivalent

design of CZH4316 which was fitted between mini special black arches. Sold per side.

($9.84) £9.84 exc vat

($11.81) £11.81 inc vat
Mk1 WIPER MOTOR MOUNTS (THREE REQUIRED)
17H5431

Wiper mounting kit for Mk1 Mini's (3 required per car). Each kit comes with a pin, nut, 2 washers and mounting rubber.

($2.50) £2.50 exc vat

($3.00) £3.00 inc vat
WHEEL ARCH FIXING KIT FOR MS127 MINI MIGLIA ARCHES
MS127FK

Wheel arch fitting kit for MS127 Mini Miglia arches.

($14.81) £14.81 exc vat

($17.77) £17.77 inc vat
MINI MIGLIA WHEEL ARCHES
MS127

Curley fibre glass Mini Miglia wheel arches, approximately 4.8." wide, with front edge 6.9" at widest point. Requires MS127FK brackets. Probably the largest wheel arches used on minis. Please note these are white gel coat not black and w...

($75.00) £75.00 exc vat

($90.00) £90.00 inc vat
WHEEL ARCH SET GROUP 2 PREMIUM BLACK
C-AJJ3316BLACK

Group 2 fibre glass wheel arches in premium black finish not requiring paint, judged the best on the market available by our customers, they stick out 1.75" including lip, when bodylines (wheel arch and moulding lip) are kept original. Screws are vis...

($85.50) £85.50 exc vat

($102.60) £102.60 inc vat
WINDSCREEN WASHER JET Mk1/2 original shape
GWW807

Original shape washer jet for Mk1/2 minis. Made to the same specification as the last type made for rover parts sales with a nut on a loose thread so it can be tightened easily by hand in the engine bay without any modifications. Should be used with ...

($3.50) £3.50 exc vat

($4.20) £4.20 inc vat
FRONT FLOOR PAN CLIP FOR FUEL AND BRAKE PIPE TAB T...
ALA5527

Clip under front floor fitted to 1990 for holding fuel/ brake lines (2 per car)

located beside floor pan footwell and tunnel

($5.00) £5.00 exc vat

($6.00) £6.00 inc vat
CLIP FOR 14A8009 MOULDING
14A8010

Special clip for the lower brightwork moulding 14A8009 for finishing off the lower dash, crash pad rail, or on earlier cars the painted metal surface of the panel which holds the switch panel section.

The moulding 14A80...

($1.22) £1.22 exc vat

($1.46) £1.46 inc vat
BONNET STRAP BLACK ORIGINAL WORKS TYPE-SINGLE
C-AJJ3380

This very heavy duty bonnet strap is a excellent reproduction of the original factory Special Tuning department special. A copy of our Tan leather strap, but now available in black.

3.3mm thick from the tanneries for use on horse bridles,wit...

($13.65) £13.65 exc vat

($16.38) £16.38 inc vat
ROOF MOULDING CLIP IN STAINLESS STEEL
DBE10006S

Roof gutter trim clip in stainless steel, ideal finishing item for our MT632 roof gutter trim.

($2.00) £2.00 exc vat

($2.40) £2.40 inc vat
ROOF MOULDING PAIR BLACK
YGA1105

Minispares 2 piece plastic roof moulding kit specially shaped for the corners and drain holes as fitted from 1980on in black.

The 2 joining and finishing clips are DBE10006PMD which need to be ordered seperately. The last Rover...

($79.00) £79.00 exc vat

($94.80) £94.80 inc vat
WASHER BOTTLE SPRING CLIP MK1/2
24A1387

Original MK1/2 shape Windscreen washer cycle type bottle clip, about 1964 on.

Has yours disappeared, or just disintegrated with age?

The original winguard MK1 bottle part number was ADA3833 NOW 17H2536 for MK1/2.
<...

($4.85) £4.85 exc vat

($5.82) £5.82 inc vat
PLASTIC NUT FOR FUEL LINE PROTECTOR AND CAT HEATSH...
EYH10001

This is the small plastic nut used to hold the fuel line protector shield on later cars, also used to hold the catalytic converter heat shield on, 4 required for each shield.

($1.07) £1.07 exc vat

($1.28) £1.28 inc vat
SPORTSPACK WHEEL ARCH FIXING STUD
ZUA000250

Fixing stud for latest new type genuine Sportspack arches. (Five required per arch)

($0.47) £0.47 exc vat

($0.56) £0.56 inc vat
WASHER BOTTLE MK1/2 ORIGINAL TYPE
17H2536

Original MK1/2 shape with correct 1.25" small neck.

Originally made by Winguard these plastic washer bottles for early Minis were often asked for but rarely available.

The original part number for the Winguard MK1 bottle was ADA383...

($14.75) £14.75 exc vat

($17.70) £17.70 inc vat
SCRIVET FOR SPORTSPACK WHEEL ARCHES
AWR2227A

The scrivet for holding the front of the rear wheel Sportspack arch and the rear of the front arch. Rover also used rivet RY612535 as an alternative.

($0.60) £0.60 exc vat

($0.72) £0.72 inc vat
BLACK RIVET FOR PLASTIC ROVER WHEEL ARCHES
ADU8629

Factory fitted rivet for the mini special wheel arches, the plastic type fitted as standard from 1984 to cover 12" wheels.

16 required but beware of the front rivet on the rear wheel arch as it goes through a double skin. 5/32" TYPE 7/16" LO...

($0.20) £0.20 exc vat

($0.24) £0.24 inc vat
RUBBER SILL MOULDING FINISHER 1993-2000
DDJ10002MS

In 1993 the moulding between the wheel arches was changed from black plastic to rubber and was still used on twin point rubber arches. This is the Minispares version which is a slightly more rounded profile.

($5.60) £5.60 exc vat

($6.72) £6.72 inc vat