CAMSHAFT 290 SCATTER CAM A PLUS SLOT DRIVE
MD290SPM

($257.40) £257.40 exc vat

($308.88) £308.88 inc vat

Special orderSpecial order
The scatter cam range are designed to give more torque,power and usable rpm than their equivalent single pattern cams. This cam is best suited to a high compression,with a 1990s engineered 649 cam that gives a good power band in standrad stroke 1275c...

($257.40) £257.40 exc vat

($308.88) £308.88 inc vat

Special orderSpecial order

Recommended usage 1 x MD290SPM to fit one mini.

People also bought products
CAMSHAFT GEAR LOCKTAB
2A759

If you are replacing your timing chain or just doing routine maintenance a new locktab is sure to come in handy.

($0.52) £0.52 exc vat

($0.62) £0.62 inc vat
REPLACEMENT BELT FOR TIMING BELT DRIVE KIT -
BELTBELT

Timing belt camshaft drive systems have been around for a number of years, in fact for a lot longer than the life expectancy of the belts. If you have a belt drive conversion you should have one of these replacement belts. If you want to keep things ...

($37.50) £37.50 exc vat

($45.00) £45.00 inc vat
DUPLEX CHAIN AND STEEL GEARS LIGHTENED SET
C-AJJ3325

Ultra light non-adjustable steel duplex timing gear and chain set with locktab and countersunk screws AEA687.

See C-AJJ3325EVO with limited stretch race quality chain.

If you are working on your engine and ...

($59.22) £59.22 exc vat

($71.06) £71.06 inc vat
CAM FOLLOWER LIGHTENED SET
C-AEG579

Set of 8, original leyland ST product but now made for us to our specification. Critical to the life and performance of the camshaft is the use of high quality cam followers. Remember, they operate in a finite hole and thus the dimensional tolerances...

($23.30) £23.30 exc vat

($27.96) £27.96 inc vat
73.5mm POWERMAX PISTON 9cc dish - SINGLE
P20659-00

For the ultimate in 1275cc overbored engine performance, double heat treated pistons. You can't beat cubic inches for performance, and the A-Series block can be bored far bigger than the factory ever imagined. The standard bore is 70.6mm, the 1380 bo...

($99.27) £99.27 exc vat

($119.12) £119.12 inc vat
TOOTHED BELT ON C-AEG455/C-AEA477/8
C-BELT255

tooth belt drive fan belt

this is for the tooth belt drive crank pulley to the 28 tooth water pump pulley

($9.30) £9.30 exc vat

($11.16) £11.16 inc vat
CORE PLUG COOPER S BLOCK
AEH592

Cup type core plug for all cooper S only @ 41.4mm wide.

4 required per engine.

($0.84) £0.84 exc vat

($1.01) £1.01 inc vat
TOOTHED BELT FOR C-AEA479/80 ON 477/8
C-BELT210

special toothed belt for cooling belt drive kits

For alternator pulley to 28 tooth water pump pulley

($9.60) £9.60 exc vat

($11.52) £11.52 inc vat
OIL PRESSURE REGULATOR KIT WITH CHROME KNOB
HPS4

This kit includes a new oil galery plug with an adjustable knob and a washer which is used as a spring seat in the plug against the relief spring. This makes a playform for the adjuster bolt to adjust the engine oil pressure. Winding the knob in incr...

($15.65) £15.65 exc vat

($18.78) £18.78 inc vat
PRIMARY GEAR FRONT FLOATING BUSH 1275cc
C-AEA3240

This is our racers favourite way of dealing with the worn or troublesome front primary gear bush.(this is NOT the top hat type rear bush)22.5mm wide. Racers and professional engine builders will use their own tolerances but these are set for road use...

($18.15) £18.15 exc vat

($21.78) £21.78 inc vat
CORE PLUG 1300 & ALL A+ ENGINES
AEC876

Cup type core plug for all A plus and 1275cc engines except for Cooper S. 33.6mm wide.A plus 5 required but only 4 on 998 A plus. 1275 has 2 core plugs oil pump end of block whereas 998 only has one

($0.77) £0.77 exc vat

($0.92) £0.92 inc vat
TIMING COVER OIL SEAL THROWER
12A1148

As soon as you take your timing cover off you should be faced with this oil thrower which helps protect the oil seal from excess leaking.

($1.53) £1.53 exc vat

($1.84) £1.84 inc vat
OIL PUMP TURBO TYPE
GLP110MS

Turbo oil pump, highest flow available. 9 Gallons per minute as against approx 6 GPM. This pump is a late model slot drive and will fit into any 1275cc engine and exactly the same as the second generation of pump as sold by Unipart/Rover.

Ga...

($30.38) £30.38 exc vat

($36.46) £36.46 inc vat
OIL PUMP 998cc A PLUS SLOT DRIVE
GLP139

3 Bolt hole fixing pump for A plus 998cc engines. This has a spade type drive spindle to fit the slot in the camshafts. This replaced earlier peg type drive which fitted into camshafts with a pin (known as pin drive).

($16.04) £16.04 exc vat

($19.25) £19.25 inc vat
CAM FOLLOWER HI-GRADE TAPPET SET OF 8
C-AEG580

The ultimate cam follower with oil hole, designed to minimise float and jump normally seen in original cam followers, which ultimately loses power. Precision ground outside diameter with smaller chamfered base to give more surface area for extra hi l...

($29.06) £29.06 exc vat

($34.87) £34.87 inc vat
CRANK DAMPER V PULLEY PRE MPI
AHU1878

Vibration Harmonic Damper-original style-less inner metal timing plate on A PLus

Alternative is 12A367 and C-AEG454

It might surprise you to know that the A-Series engine has a vibration problem! But the f...

($120.00) £120.00 exc vat

($144.00) £144.00 inc vat
ENGINE STABILISER BAR ADJUSTABLE AS FITTED TO TURB...
MSSK1305

Adjustable engine upper stabiliser rod.

Copy of ERA 1020 adjustable rod as fitted to the ERA mini turbo for clearance reasons. This adjustable rod takes the standard rubber bushes or equivalent and is a useful means of pushing the top of the...

($21.42) £21.42 exc vat

($25.70) £25.70 inc vat
CENTRE MAIN STRAP & BOLTS - 1275cc BLOCKS
CMS13

Steel centre main strap for large bore engines, comes with longer high tensile bolts. Main top cap needs machining flat, no other modifications required.

On all performance A series engines it is essential to ensure accurate and as near perm...

($11.90) £11.90 exc vat

($14.28) £14.28 inc vat
VALVE EXHAUST LONG STEM 31mm. heat treated for unl...
C-AEG107

1.220" (31mm) dia x 3.57 exhaust valve.

Our race valves are produced in EN214N steel and are stellite tipped and use the later narrow, single collet groove and current valve head shapes.These valves are plasma heat treated to eradicate wear ...

($17.69) £17.69 exc vat

($21.23) £21.23 inc vat
HEAD GASKET COPPER PERFORMANCE 1275. MINISPARES OW...
GEG300

Genuine Mini Spares Performance Copper/steel head gasket.

Based on the original AF460 pre 2000 design plus the old Payen Special tuning C-AHT188 with superior sealing rings.

With modern day technology and NON asbestos l...

($17.70) £17.70 exc vat

($21.24) £21.24 inc vat