($53.92) £53.92 exc vat
($64.70) £64.70 inc vat
In stock
For wind up window cars 1970 on this is a set of inner and outer door brightwork mouldings with rubber seals attached to stop water running down the windows causing rust and to prev...
($53.92) £53.92 exc vat
($64.70) £64.70 inc vat
In stockRecommended usage 1 x MSSK2101 to fit one mini.
Genuine Mini Spares mouldings product as supplied to Rover.
These are the later door mouldings that prevent water running down the windows into the door causing rust and have the black platic ends fitted for later car safety regulations but ...
Trim clip for fitting the stainless/rubber window moulding (EJU10003) on to the door. Sold individually.
Genuine Mini Spares mouldings.
These brightwork steel mouldings include the rubber window scraper, are standard on all wind up window minis and are also available with the black plastic ends introduced as a safety requirement on later minis....
Lower moulding clip for wind up window mouldings..4 PER SIDE required but sold singly-Fits CZH1666/7 and PAM1014/5
Also used for 24A1169 glove box moulding MK1/2.
Genuine Mini Spares product as originally made by Pianoforte and then Mini Spares for Rover.Clips for this are EYC10048
This is the 1/2" tall thinner type fited to wind up window cars from 1970 on.
The original 1" talle...
Complete car set of rear sliding window runners for Mini Estate and Countryman models.
High quality non genuine door check strap for MK3 cars with wind up window doors (use with retaining pin CLZ412). Beware there are cheap copies on the market that are poor quality and when fitted to our cars did not function correctly!
Genuine Mini Spares Mk3 window drop frame in stainless steel. Supplied with the rubber seal.
Genuine Mini Spares Mk3 window drop frame in stainless steel. Supplied with the rubber seal.
The gasket that sits behind the door stiker on all wind up window type minis
on the B post.
Rear screen seal for mk1 cars which had the smaller rear window 1959-1967.
Complete fitting kit for the door check straps on all Minis fitted with external hinges.
Angled spacer washer for Mk1/2 external door hinge cars for the upper hinge
This screw can used to hold together the 2 halves of the disc shields on all
mini front discs. fits MK1/2 door escutcheons.
Use SE910161 and cut down to 3/8" long including head
PMZ306 was originally 3/8"long u...
Full Mk2 door handle set with 2 front door locking handles and boot handle with matching keys. Fitted from 1966 with the intoduction of the door safety escutcheon boss. This boss is available as 24A1834 and gasket 24A1835.
Regre...
The black windsreen and backlight rubber fillet. Chrome is more popular however.
A single length for a single screen is 37H8052
Front and rear screen with chrome plastic insert.Saving nearly 15% on cost of individual partts
A great accessory for wind up window minis. Fitted in minutes to make such a difference driving your Mini with the window open. Wonderfull for those that smoke or love fresh air. In a tinted colour to stop bad reflections.
Twin point injection cars had a split seal system door frame seal for the front doors,the lower acting as a shield cover for the trim, fitted from chassis no BD134455 ON
Some customers have replaced it by the one piece CGA2835MS<...
Twin point injection cars had a split seal system door frame seal for the front doors,the lower acting as a shield cover for the trim. fitted from chassis no BD134455 ON
Some customers have replaced it by the one piece CGA2835MS<...
Special lower seal--fitted to MPI cars from October 1996 show cars chassis no BD134455 ON
Has a lip on inner edge to hold carpet back and tidy internal trim but other than that the CGA2835MS will fit --the full set is
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.