Door Pull Handle Grey 85 on
YXX451LOY

($3.00) £3.00 exc vat

($3.60) £3.60 inc vat

Out of stockOut of stock
Most of the door pull handles were black but some mayfairs had these grey type fitted. Being sold at a clearance price.

($3.00) £3.00 exc vat

($3.60) £3.60 inc vat

Out of stockOut of stock

Wind up Window Doors - Qty 2

People also bought products

The rubber type grip fitted on handbrakes-

will fit any single cable hand brake from 1976 on

Mk1/2 used 13H5541 thinner plastic type--to fit this to pre 1976 early cars you will need to put lots of sticky tape on the h...

Rectangular grey plastic with white plastic interior lamp was fitted to minis from 1974 until 1985. 4.25" long and 1.75" wide. From 1984 on Rover recessed the lamp AFU4092 into the headlining. Fitted with GLB239 bulb. The le...

Multi purpose square plastic plug/nut for No8 screw size was used on many door fixings and fuse box to body.



Also suitable for Twin Point indicator fixings.

The black plastic door pocket as fitted to mini metro and minis on wind up window type doors.

This is the chrome screw that fits the 14A8151 catch boss on sliding window minis. Also fits the door winder handle on early wind up window cars.

Uses ADU8081 screw and YXX3200PA cover. With a spring loasded winder knob this handle was fitted to later cars as a safety requirement. Fitment was from 1983 but fully introduced in 1984

black plastic knob for seat adjust handle and on bonnet opening slider for some cars

The special pointed shape buffer locates against the boot board of Cooper S and variants where a factory type boot board is fitted.

Dark grey carpet set with edge binding. Why not fit CARPET01 clip set to make the job complete. Made to fit any saloon they are perfect fit for rod change cars but pre 1973 with the little bulge on the round tunnel where floor start used...

Lower moulding clip for wind up window mouldings..4 PER SIDE required but sold singly-Fits CZH1666/7 and PAM1014/5

Also used for 24A1169 glove box moulding MK1/2.

Fitted on cars up to about 1982 approximately before spring type knob on handle was introduced for safety homologation YXX3199PA.

The screw this CZA7109 handle is ZKC3317.

Brake or clutch pedal pad for MK4 from 1976 on. In 1990 they improved this pad by introducing SZU10001 which is a far superior product.

Seat Spacers.

If you think you are too tall for the Mini. These brackets allow you to really stretch out.

This plastic clip was commonly used by Rover for all car trimming and first found its way on the wind up window version mini door panel.9 per side but always purchase a spare in case of breakages.

The stock bare metal handle can be cold, clammy and slippery; this rubber grip slips on the handle for added comfort on all cars with twin handbrake cables.

This plastic handle fitted any wind up window cars up to the introduction of the twin points, which then changed and the handle fitted from 1996 on is now obsolete.

Mini Spares genuine product-plastic 2 piece casing for the steering wheel cowl was introduced in 1976 which was for the introduction of twin indicator stalks and a different steering lock. Twin point injection cars have different cowling and switches...

This pump was fitted to the strange shaped, tall looking washer bottle GWW935 fitted under the bonnet with an integral fitted electric washer pump, fitted from 1990 until the location was changed to the boot area on single point injectio...

White with mirror aftermarket sun visor for Mk3 models from 1977 -92 which were thinner than pre December 1965 for safety crash requirements. Check out the special clips to hold these visors as they are sold seperately in car sets only as [link]SV202...

A car set of 4 special plastic clips and screws to hold in the sunvisors from december 1965 on SV2016P, SV2016W and SV2017P, SV2017W. For use on visors from 1965 that have a hinge either end.