£108.00 exc vat
£129.60 inc vat
In stock
see 2A3492 for the special bolt
see NT604041 for the thin nut
see ghf321 for the washer
£108.00 exc vat
£129.60 inc vat
In stockRecommended usage 1 x 22A610 to fit one mini.
1st/2nd gear change forks are prone to wear. This one is for the 4 synchro pre rod change gearbox only.
Newly re-tooled and manufactured in the UK, lost wax cast in aluminuim bronze.
see 2A3492 for the special bo...
Anybody proud enough to still be driving around with their 3 syncro gearbox needs all the encouragement they can get! We are pleased to be able to still provide these to keep the car alive and feeling like new. The shift forks are made of a brass t...
Left hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used. For R/H locktab see 22A962
Right hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used.
Solid dowel at the front of the engine that locates the block to gearbox.
Bolt that holds elector fok to change rod on Pre A plus gearboxes.
both remote and magic wand type
Single roller bearing that only fits 3 synchro gearboxes to hold the 1st motion shaft-sporadic stocks only of these bearings as they went obsolete in 2008. These are genuine RHP/NSK bearings
Used on all mainshafts with 14mm shaft end for the 1st motion shaft---when they went to the 18mm shaft on A plus gearboxes they used DAM7485 which is metric thread.
THIS BEARING HAS PRE A+ INNER DIAMETER AND A+ OUTER DIAMETER. If you have the large A plus idler gear bearing hole and want to use it for the earlier pre A plus small hole type idler gear then this bearing is what you require to sleeve it down in siz...
The shims go against the mainshaft double roller bearing securing cap in your gearbox to give it pre load. See workshop manual for advice but you are aiming for only 1 thou pre load.
Idler gear shims for the Pre A Plus gearboxes with 0.750" (19mm) size shafts
Quantity required per gearbox is 2 but idler gear shims require shimming for correct clearance 3-6 thou as per workshop manuals but 3 thou for road and 4 thou for r...
Genuine 1ST Motion shaft SINGLE track original bearing for 4 synchromesh 1st motion shaft.
This is a Genuine RHP bearing, and should not be confused with cheap alternatives. The cheap aftermarket bearings often fail and the work involved to...
This little roller bearing goes inside the end of the 1st motion shaft on minis with 14mm mainshaft which it sits on.
This bearing was previously part number 88G409 and a true Rover replacement, but if you have earlier A type gears with the...
Mini Spares Performance Baulk ring.
The standard sintered baulk (synchro) rings are not tough enough for the demands of performance useage, in many instances lasting only one race before failure or breakage. The main reason is the incompat...
Genuine RHP as originally fitted to every production Mini.
Two of these main diff carrying bearings are required in the gearbox and this new steel caged type fits either way round. Should be pre loaded by 1-2 thou.
Some original fi...
Genuine Rover later type held in by roll pin.This is the only selector fork available for the rod change 3rd and 4th gear change. Secured in place by a roll pin (available as 22G2595) it replaces the earlier type which was held in place ...
The bronze washer for the planet gears in the differential for pre A plus gearbxes. You can use the DAM5071 and cut the lips off.
Anybody proud enough to still be driving around with their 3 syncro gearbox needs all the encouragement they can get! We are pleased to be able to still provide these to keep the car alive and feeling like new. The shift forks are made of a brass t...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.