£29.07 exc vat
£34.88 inc vat
In stock
A 15" & a 25" long line makes these kits ideal for those wanting to relocate the oil cooler!
£29.07 exc vat
£34.88 inc vat
In stockRecommended usage 1 x MOC100102 to fit one mini.
These braided oil cooler hoses are the best available and although longer for the mini clubman many mini racers use these for the extra length to enable fitting to a standard mini. Short Pipe: 14" Long Pipe: 24"
Oil cooler union for later cars, will fit the oil filter head and block, 1/2" BSP to 11/16". Requires DSM18 to seal. These are handy when you have changed to a later filter head etc and want to fit an early oil cooler kit.
Oil cooler kit for MPI models. Oil cooler is 10 rows, 21cm long and 9cm high. Unions are 18mm and require the special fitments as supplied in this kit. The oil filter is GFE210
5/8" straight connector piece for heater hose modifications on late minis.
Useful when re-routing hoses or joing hoses.
1" long from bend to take a push on fit 1/2"hose-has 1/2"BSP thread to fit oil cooler and has 45 degree angle bend
1" long from bend to take a push on fit 1/2"hose-has 1/2"BSP thread to fit oil cooler and has 90 degree angle bend
For minis with 5.8"UNF size oil pipe block hole 1/4"npt filter head (pre 1991 12A engine) but with a pre-engaged starter longer pipes are required 15" block and 22" filter.
Set of engine block and filter head unions for pre 12A engines (1992).
these take push on oil cooler hose.
These braided oil cooler hoses are the best available and although longer for the mini clubman many mini racers use these for the extra length to enable fitting to a standard mini. Short Pipe: 14" Long Pipe: 24"
Oil temperature sender unit housing for checking oil temperature.
Fits into the oil cooler hose.(Not compatable with braided hoses) Fitted before the oil cooler will show maximum temperature reached. After the oil cooler it will tell you the...
A must for road use when an oil cooler is fitted.
In the past, fitting an oil cooler was mandatory once an engine had been even slightly uprated. The main reason for this was the quality of motor oils available at that time. If the oil temp...
Special formulated hose for oil, this is for people who have special oil cooler fittings and ends that use lengths of hose. This 1/2" hose is also used for all closed circuit breather systems and uses 3H2963 clips. SOLD AS REQUIRED PER F...
Usefull joining union for 1/2" water hoses and used for oil coolers hoses.
The original union that fitted on the A series block to take the oil cooler hose. Many kits now include the union as part of the hose. Filter head size 1/4"NPT.
These are the original brackets (2 required) used to fit on the front subframe to hold the oil cooler. For later cars check you have clearance.
SOLD INDIVIDUALLY.
It is critical to understand that an oil cooler is not designed to last the life of the car. Sound maintenance practice tells us that whenever we are doing a major engine overhaul we should not fail to replace the cooler as it is almost impossible to...
genuine Mocal UK cooler.This is the ideal size for minis, but everybody goes for the 13 row type cooler radiator C-ARH221 which was fitted to the Cooper S eventually as standard but that was over 30 years ago, before the later type oils ...
A low oil pressure warning light switch is available to help protect the engine. The standard one comes on at 7lb-much too late to avoid damage. This one comes on at 20lb and is adjustable up to 120lb. Please note this is now a twin terminal switch, ...
Too big for normal use, only used for special requirements. It is critical to understand that an oil cooler is not designed to last the life of the car. Sound maintenance practice tells us that whenever we are doing a major engine overhaul we should ...
Fitting kit comprising of studs, nuts, plain washers, spring washers and a gasket
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.