£7.43 exc vat
£8.92 inc vat
In stock
Require a recess of 1.2495"(31.737mm) diameter, plus or minus 0.0005" (0.013mm), and 0.250"(6.35m) deep at ambient temperature of 20C.
£7.43 exc vat
£8.92 inc vat
In stockRecommended usage 4 x TAM2069 to fit one mini.
As an engine wears, the clearance between the valve stem and guide increases; as this gets beyond tolerances the car will tend to smoke under deceleration (when you take your foot off the throttle). Good valve stem seals will allow for greater wear b...
That tell tale puff of blue smoke when you first start is an indicator of worn guides or seals. Valve guides should be replaced with every valve job.
Sold individually, these are the original quality Cooper S guides for use in any head espec...
New colour, PB104 bronze guides.Although Silicon bronze valve guides were used for their extremely good wear values, they were very hard and not user friendly when fitting. These valve guides are recommended when using all EN21 4N stainless steel val...
Genuine Mini Spares valve stem oil seal manufactured with original Dupont Viton, as fitted to the twin points engines, are the best material and seal you can use and although expensive are the best to date in stopping the engine smoking.
Man...
35.7 x 29.5mm race valves in plasma-nitrided EN214N s/steel with manganese bronze valve guides. Nominal 21.4cc with by pass and heater take off holes open.
This specification of cylinder head, based on used core castings, is modified to curr...
35.6 x 29.3mm valves in chrome stem with cast iron valve guides. This specification of cylinder head, based on used core castings, is modified in true Road sport style to maximise on-road performance for those wanting maximised drive-ability when ...
35.7 x 29.5mm race valves in plasma-nitrided EN214N s/steel with manganese bronze valve guides, Nominal 21.4cc with by pass hose and heater take off holes open. This specification of cylinder head, based on used core castings, is modified to current...
35.7 x 31mm race valves in plasma-nitrided EN214N s/steel with manganese bronze valve guides. Nominal 21.4cc with by pass and heater take off holes open.
This specification of cylinder head, based on used core castings, is modified to curre...
35.7 x 29.5mm valves in plasma-nitrided EN214N s/steel with manganese bronze valve guides.Nominal 24-25cc with by pass and heater take off holes open. Supersport head-sold on an exchange basis-old core must be serviceable and no cracks--See [link]...
35.6 x 29.3mm valves in chrome stem with cast iron valve guides.
By pass hose tube and heater outlet open. This specification of cylinder head, based on used core casting, is modified in true Road sport style to maximise on-road performance ...
New competition valve cotter for early heads with the large single groove valve, these are precision CNC machined from 4340 and heat treated to a better spec than EN24T and claimed to be stronger in fatigue life.
These locate better in the v...
New competition valve cotter, these are precision CNC machined from 4340 and heat treated to a better spec than EN24T and claimed to be stronger in fatigue life.
These locate better in the valves and easier to control spring heights.
Set of strong lightweight titanium top caps to suit our valve springs C-AEA526/527 hard for single collet competition valves. Sold as a set of 8.
Genuine Mini Spares valve stem oil seal manufactured with original Dupont Viton, as fitted to the twin points engines, are the best material and seal you can use and although expensive are the best to date in stopping the engine smoking.
Man...
EXHAUST VALVE 1.15 TURBO
.3135 thou (7.96mm) thick, uses CAM6573 collets only.
Sold individually.
To help rocker pad to valve stem alignment and reduce friction, the standard springs can be replaced with solid spacers and correctb shim set. The spacers and shim kit are sold as C-AEG392.
Spacers for under the rocker pedestals are used mainly by engine tuners to allow tappet adjustment to be made where cylinder head mods have been carried out. 1.3mm/0.0512" thick, this can be used to hold locating screw on rocker post assembly but the...
Early Large cotter groove exhaust valve. Most small bore engines seem particularly prone to burning valves, it is highly recommended to replace the exhaust valves when you do a valve job! This 1.0" valve fits most early 948cc, 998cc and 1098cc engine...
We stock a limited range of Paul Ivey developed Rimflow valves for the A-Series.
30.9mm (1.217") diameter exhauste valve for 12G940 large bore casting is oversized to the stock version. Not only can you pick-up performance from...
1.402" (35.6mm) dia x 3.57" long intake valve.
Our race valves are produced in EN214N steel and are stellite tipped and use the latest triple collet groove and current valve head shapes, plasma heat treated for eradicating unleaded petrol we...
1.311" (33.3mm) dia x 3.57 long intake valve.
Our race valves are produced in EN214N steel and rquire Manganese/Silicon bronze alloy valve guides. use the later narrow, single collet groove and current valve head shapes.
As ...
1.259" (32.00) dia x 3.57 long Exhaust valve.
Our race valves are produced in EN214N steel. They are stellite tipped and use the later narrow, single collet groove and current valve head shapes.Heat treated to eradicate wear from unleade...
1.220" (31mm) dia x 3.57 exhaust valve.
Our race valves are produced in EN214N steel and are stellite tipped and use the later narrow, single collet groove and current valve head shapes.These valves are plasma heat treated to eradicate wear ...
1.401" dia x 3.52" long intake valves. Our race valves are produced in EN214N steel, stellite tipped and use the later narrow collet groove and current valve head shapes. As it is possible, even common, to swap one head for another on 1275 engines, i...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.