£21.76 exc vat
£26.11 inc vat
In stock
£21.76 exc vat
£26.11 inc vat
In stockRecommended usage 1 x 08-524300-10 to fit one mini.
Standard Size with 0.59" compression rings and 0.1181" oil ring for 998cc
These Swiftune die cast performance pistons are part of their new Heritage range and are manufactured by global leading German F1 piston manufacturer Mahle. These pistons have been developed using their 50 plus years of experience.
Glyn Swif...
Steel ring set with 3 piece oil rings as preferred by engine builders for P21253 pistons.
Standard Size with 0.59" compression rings and 0.1181" oil ring for 998cc
3mm OIL RING with compression ring size .0591" (1.5mm)and one piece oil ring .1181" (3mm)on p21253 pistons giving 9.7cr on 1275cc. std ring size
For performance see steel ring set with 3 piece oil ring as favoured by engine builders[link]C1...
20 thou oversize low drag slipper type pistons for modern day compression ratios and unleaded fuel.
Typically installation will result in a minimum 8.8:1 compression ratio but on some pre 1984 Metro versions it was higher.
Current...
Replace with new camshaft,it's almost too easy to overlook during a rebuild. Camshaft bearings are pressed into the block and thus are usually done by a machine shop. You would not rebuild an engine without replacing the rod bearings, so why not the ...
Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).
You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all late model 1275cc blocks (the ones without tappet covers on the back) It's almost too simple and thus often overlooked during a rebuild. Ca...
High quality 817M40 forged steel conrod set. Lightweight std length 5.75" Cooper 'S' conrod ONLY FOR USE with special 18mm gudgeon pin pistons. Conrod weight 453g. Arp 2000 bolts. Manufactured in the UK by Arrow Precision Engineering.
These...
Con Rod bearings, 850-1275 1 5/8" journals. Heavy duty steel backed bearing for durability and long life. The bearings to use if you want it to last. The only bearings to use on a fast road motor.
( Tri-Metal )
Sintered copper lead...
Mini Spares cam follower with original convex bottom Radii as used by BMC/Rover and made by Clanceys but less the oil hole. Using Clancey drawings and to our design for better cam performance and lift we have made the push rod recess deeper for stabi...
Price per rod-850/998/1098cc larger 6.35mm diameter. One piece rod which are sold per single rod and 8 required per engine.
The larger diameter improves push rod rigidity as much as possible
without having to modify the block/head ...
The oil pressure relief valve consists of an aluminum plunger with a heavy spring behind it. Access is through the 15/16" domed cap nut beside the dizzy. Once this nut is removed the spring will be visible. The plunger is beneath the spring and will ...
Replace with new camshaft,it's almost too easy to overlook during a rebuild. Camshaft bearings are pressed into the block and thus are usually done by a machine shop. You would not rebuild an engine without replacing the rod bearings, so why not the ...
Mini Spares Non genuine timing chain gasket fitted to every BMC A series engine with 10 gasket holes until the introduction of the A plus type which had a bulge in its side where the tensioner was fitted which had 11 holes.
Gasket material h...
Mini Spares quality gasket. When the factory introduced a timing chain tensioner to single row chains on the A plus engines they had to change the shape of the front plate giving it a bulge. This is the gasket for A plus engines only.
Standard size crankshaft washers as a set of four, fits 998 and 1100cc.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.