BELL CRANK PIVOT PIN FOR ROD TYPE BOX ONLY
22G1845

£19.91 exc vat

£23.89 inc vat

In stockIn stock
The pin in the bottom of your gearbox that holds all the gearchange levers.

These parts might be slightly soiled as they were from new gearboxes stripped down from Rover powertrain before they closed the plant making these parts obsolete whe...

£19.91 exc vat

£23.89 inc vat

In stockIn stock

Recommended usage 1 x 22G1845 to fit one mini.
Rod Change Gear Selectors and Speedo Drive - Qty 1
Gearbox Selector Forks - Qty 1

Alternative products
BELL CRANK PIVOT PIN FOR ROD TYPE BOX - SECOND HAN...
22G1845MS

The pin in the bottom of your gearbox that holds all the gearchange levers.

These parts are soiled but usable as they are used.

£10.00 exc vat

£12.00 inc vat
People also bought products
PINION "C" SHIM .004"
GUG705646GM

The shims go against the mainshaft double roller bearing securing cap in your gearbox to give it pre load. See workshop manual for advice but you are aiming for only 1 thou pre load.

£0.79 exc vat

£0.95 inc vat
BALL BEARING FOR DETENT SPRING
BLS110

When you take the side cover off the differential housing on a rod change type gearbox this detent ball sits behind the spring-the spring is 22G2083 and the sleeve is 22G1870. The oil seal for this is 22G1417.

£0.22 exc vat

£0.26 inc vat
SELECTOR FORK 3RD/4TH GEAR ROD CHANGE
TSP100400

Genuine Rover later type held in by roll pin.This is the only selector fork available for the rod change 3rd and 4th gear change. Secured in place by a roll pin (available as 22G2595) it replaces the earlier type which was held in place ...

£75.00 exc vat

£90.00 inc vat
BALL BEARING FOR SYNCHRO HUB 3&4 SYNCHRO
BLS107

Inside your gearbox synchro hubs are 3 springs and these ball bearings to lock it in and out of gear. Often pop out and get lost when splitting the inner and outer hub.

£0.45 exc vat

£0.54 inc vat
LEVER ROD LOWER.ROD GEAR CHANGE
22G1847

For the rod change gearbox, this is the lower of the 2 bell lever cranks that sit on a pivot pin on the bottom of the case. The upper one is 22G1848 and the larger protruding one at the very bottom, AHU2292 is for reverse. The fork has 2...

£11.20 exc vat

£13.44 inc vat
DETENT SPRING FOR ROD BOX
22G2083

When you take the side cover off the differential housing on a rod change type gearbox this detent ball spring sits on a ball bearing BLS110 and the sleeve is 22G1870. The oil seal for this is 22G1417.

£0.27 exc vat

£0.32 inc vat
SELECTOR FORK 1ST/2ND GEAR SELECTOR FORK ROD CHANG...
TSP100390

Later type held in by roll pin.The shift fork in all gearboxes are designed to take a lot of abuse. They have to cradle a gear spinning at high RPM while forcing it into the next position. As the gears have to be made of very hard steel, the shift ...

£85.50 exc vat

£102.60 inc vat
PINION "C" SHIM .002
GUG705645GM

2 thou shims to go against the mainshaft double roller bearing securing cap in your gearbox to give it pre load. See workshop manual for advice but you are aiming for only 1 thou pre load--these were sold by Unipart as 3 thou but the Rover drawing we...

£0.70 exc vat

£0.84 inc vat
ROLLER 1ST MOTION SHAFT PILOT TO CLUTCH CASE GENUI...
AAU8424

Genuine RHP Outer support bearing for the first motion shaft. Comes with bearing and outer race. You MUST REPLACE the outer race when using the new bearing. An easy way to remove the old race is to clean the housing very well, remove the circlip, and...

£28.23 exc vat

£33.88 inc vat
LOCKTAB MAIN DOUBLE ROW BEARING HOUSING IN GEARBOX
DAM2377

The housing to retain the double row gearbox bearing has 4 bolt holes but the casing itself might only have 3 drilled holes where they deleted the susceptible to cracking hole on powerful engines. Originally 2 locktabs were used when four bolts, decr...

£2.01 exc vat

£2.41 inc vat
REVERSE GEAR BUSH
TUJ10001

The longer one piece bush as fitted to all late reverse gears. Early type had 2 single bushes which sometimes came adrift after arduous use.

£4.50 exc vat

£5.40 inc vat
A+ MAINSHAFT NUT
DAM7485

Mainshaft nut for original shafts with 18mm 1st motion shaft bearing nose size.

£2.40 exc vat

£2.88 inc vat
GEAR BOX DIFFERENTIAL PINION LOCKTAB
DAM6140

Gearbox differential pinion locktab to secure it on the mainshaft for all manual gearboxes.

£2.20 exc vat

£2.64 inc vat
SELECTOR FORK ROLL PIN - ROD CHANGE
22G2595

special shaped roll pin for the rod change selector forks

£1.35 exc vat

£1.62 inc vat
SELECTOR ROD.ROD CHANGE GEARBOX
22G1858

The internal selector shaft in the bottom of the gearbox which fits into 22G1844 on Rod change gearbox only.

£49.99 exc vat

£59.99 inc vat
LEVER RELEASE.ROD CHANGE BOX
22G1849

reverse release lever for rod change gearboxes only- sits on the bottom of the bell lever pivot pin on the top hat pivot bush.The 2 bell lever cranks above it are 22G1847/8. This part was superseded by AHU2292 which is now obsolete--.

both...

£33.60 exc vat

£40.32 inc vat
CIRCLIP 1ST MOTION NOSE OUTER CAGE
2A3643

this is the large clip that retains the outer track of AAU8424 bearingin your clutch case for the roller bearing that sits on the end of the 1st motion shaft. The little circlip that holds the bearing on the shaft is CCN110

£3.50 exc vat

£4.20 inc vat
SYNCHRO HUB SPRING. 4 SYNCHRO ONLY
22G2262

Only for the 4 synchromesh gearbox synchroniser gear hub. There are 3 of these per hub with BLS107 ball bearing.

£1.05 exc vat

£1.26 inc vat
1ST MOTION SHAFT NOSE CIRCLIP (PILOT ROLLER)
CCN110

The little circlip on the end of the 1st motion shaft that holds the inner race

of the pilot bearing AAU8424. The larger circlip to hold the outer track in the clutch case is 2A3643.

£1.61 exc vat

£1.93 inc vat
1ST MOTION SHAFT LOCKTAB
DAM4000

Locktab for holding the broach gear to the 1st motion shaft.

£1.76 exc vat

£2.11 inc vat